Ks0154 keyestudio Mega Pololu Shield (RAMPS 1.4 ): Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
No edit summary
 
(13 intermediate revisions by the same user not shown)
Line 1: Line 1:
== keyestudio Mega Pololu Shield (RAMPS 1.4 )==
[[image:ks0154.png|thumb|500px|right|Keyestudio Mega Pololu Shield (RAMPS 1.4 )]]
<br>[[File:ks0154.png|500px|frameless|thumb]]<br>
<br>
==Introduction==
keyestudio RAMPS1.4A is used as driving shield for 3D printers, fully compatible with [http://wiki.keyestudio.com/index.php/Ks0002_keyestudio_Mega_2560_R3_Development_Board MEGA2560 control board] and official RAMPS 1.4 .<br>
It has total 5 slots for stepper motor drive module to drive 5-channel stepper motors. The slots are compatible with all kinds of drive modules like [http://www.keyestudio.com/keyestudio-reprap-stepper-motor-driver.html A4988], [http://www.keyestudio.com/keyestudio-drv8825-stepper-motor-driver-for-3d-printer.html DEV8825]. <br>
There are 3 jumper caps under each slot, which can be used to control the working subdivision of drive modules. <br>
For example, if connect the A4988 and plug three jumpers, the subdivision port MS1、MS2 and MS3 of A4988 module are at active HIGH, so the A4988 module is in 16-subdivision working mode.
But if unplug the three jumpers, MS1、MS2 and MS3 of A4988 module are at active LOW, so the A4988 module is in full-step working mode.<br>
Furthermore, it is easy to stack it onto the MEGA 2560 control board, after burning the program, you can combine it with external devices to make your own 3D printer.<br>
[[File:KS0154 (8).jpg|500px|frameless|thumb]]<br>
 
<br>
 
==Check out these awesome features==
* MEGA 2560 control board compatible
* Supports the software Repetier-Host
* Can drive 5 stepper motors
* Control the drive module via jumper cap. (Note: If connect the A4988, unplug three jumpers, in full-step mode; if plug the jumpers, in 16-subdivision working mode.)
* Comes with 4pin headers of 2.54mm pitch for 42 step motor connection.
* Supply the voltage DC 12V for 3D printer.
* Onboard comes with 4 LEDs, separately are 2 Heat LEDs, a Heat Bed LED and a D13 LED.
* Comes with 2 Heat interfaces (D10, D9 control) and a Heat Bed interface(D8 control)
* Onboard comes with a reset button
* Comes with other interfaces for 3D Printer, such as LCD connection pins ( need to connect the pinboard), limit switch pins, cooling fan interface.
 
<br>
==Technical Details==
* Dimensions: 114mm x 61mm x 32mm
* Weight: 67.5g
<br>[[File:KS0154 Detail.png|600px|frameless|thumb]]<br>


==Introduction==
<br>
It is a Mega Pololu Shield, or RAMPS for short, designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.<br>
==PINOUT Instruction==
<br>[[File:KS0154 (8).jpg|500px|frameless|thumb]]<br>
<br>[[File:KS0154 pinout.jpg|900px|frameless|thumb]]<br>


==Specification==
<br>
* Has provisions for the cartesian robot and extruder;
==Using Method==
* Expandable to control other accessories;
When using this shield, on the hardware, you need to use it with the control board ([http://wiki.keyestudio.com/index.php/Ks0002_keyestudio_Mega_2560_R3_Development_Board MEGA2560 board]), the drive board (such as [http://www.keyestudio.com/keyestudio-reprap-stepper-motor-driver.html A4988]), the motor (42 stepper motor) and others. And you need to burn the firmware to the control board. So need to use the software [http://wiki.keyestudio.com/index.php/How_to_Download_Arduino_IDE Arduino IDE], and the special upper computer software, such as Repetier-Host software.<br>
* 3 mosfets for heater / fan outputs and 3 thermistor circuits;
For detailed use, refer to our [http://wiki.keyestudio.com/index.php/Ks0091_keyestudio_3D_Printer_Kit_RAMPS_1.4_%2B_Mega_2560_%2B_5x_A4988_%2B_LCD_2004_Smart_Controller keyestudio 3D Printer Kit] on wiki website.
* Fused at 5A for additional safety and component protection;
* Heated bed control with additional 11A fuse;
* Fits 5 Pololu stepper driver board;
* Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs;
* I2C and SPI pins left available for future expansion;
* All the Mosfets are hooked into PWM pins for versatility;
* Servo style connectors are used to connect to the endstops, motors, and LEDs. These connectors are gold plated, rated for 3A, very compact;
* SD Card add on available
* LEDs indicate when heater outputs on
* Option to connect 2 motors to Z for Prusa Mendel


<br>
==Resources ==
==Resources ==


'''Datasheet'''
'''Download the PDF:'''<br>


http://www.keyestudio.com/files/index/download/id/1464579027/
https://fs.keyestudio.com/KS0154
<br>


==Get One Now ==
==Get One Now ==
'''Website'''
*[https://www.keyestudio.com/free-shipping-new-keyestudio-ramps-14-3d-printer-control-panel-printer-control-reprap-mendelprusa-p0350-p0350.html '''Official Website'''  ]
 
http://www.keyestudio.com/keyestudio-ramps-1-4-3d-printer-control-panel-printer-control-reprap-mendelprusa.html


'''Amazon'''
*[https://www.amazon.com/dp/B01E5K98C6  '''Shop on Amazon''' ]<br>


https://www.amazon.com/Keyestudio-Printer-Controller-Arduino-REPRAP/dp/B01E5K98C6/ref=sr_1_fkmr0_4?ie=UTF8&qid=1479110616&sr=8-4-fkmr0&keywords=Keyestudio+RAMPS+1.4+3D+printer+control+panel+printer+Control+Reprap+MendelPrusa
*[https://www.ebay.com/itm/132584623480  '''Shop on eBay''' ]


[[Category: Shield]]
[[Category: Shield]]

Latest revision as of 10:35, 29 April 2021

Keyestudio Mega Pololu Shield (RAMPS 1.4 )


Introduction

keyestudio RAMPS1.4A is used as driving shield for 3D printers, fully compatible with MEGA2560 control board and official RAMPS 1.4 .
It has total 5 slots for stepper motor drive module to drive 5-channel stepper motors. The slots are compatible with all kinds of drive modules like A4988, DEV8825.
There are 3 jumper caps under each slot, which can be used to control the working subdivision of drive modules.
For example, if connect the A4988 and plug three jumpers, the subdivision port MS1、MS2 and MS3 of A4988 module are at active HIGH, so the A4988 module is in 16-subdivision working mode. But if unplug the three jumpers, MS1、MS2 and MS3 of A4988 module are at active LOW, so the A4988 module is in full-step working mode.
Furthermore, it is easy to stack it onto the MEGA 2560 control board, after burning the program, you can combine it with external devices to make your own 3D printer.
thumb


Check out these awesome features

  • MEGA 2560 control board compatible
  • Supports the software Repetier-Host
  • Can drive 5 stepper motors
  • Control the drive module via jumper cap. (Note: If connect the A4988, unplug three jumpers, in full-step mode; if plug the jumpers, in 16-subdivision working mode.)
  • Comes with 4pin headers of 2.54mm pitch for 42 step motor connection.
  • Supply the voltage DC 12V for 3D printer.
  • Onboard comes with 4 LEDs, separately are 2 Heat LEDs, a Heat Bed LED and a D13 LED.
  • Comes with 2 Heat interfaces (D10, D9 control) and a Heat Bed interface(D8 control)
  • Onboard comes with a reset button
  • Comes with other interfaces for 3D Printer, such as LCD connection pins ( need to connect the pinboard), limit switch pins, cooling fan interface.


Technical Details

  • Dimensions: 114mm x 61mm x 32mm
  • Weight: 67.5g


thumb


PINOUT Instruction


thumb


Using Method

When using this shield, on the hardware, you need to use it with the control board (MEGA2560 board), the drive board (such as A4988), the motor (42 stepper motor) and others. And you need to burn the firmware to the control board. So need to use the software Arduino IDE, and the special upper computer software, such as Repetier-Host software.
For detailed use, refer to our keyestudio 3D Printer Kit on wiki website.


Resources

Download the PDF:

https://fs.keyestudio.com/KS0154

Get One Now

Retrieved from "http://wiki.keyestudio.com/index.php?title=Ks0154_keyestudio_Mega_Pololu_Shield_(RAMPS_1.4_)&oldid=32246"