Ks0177 keyestudio RGB LED CUBE KIT: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(21 intermediate revisions by the same user not shown)
Line 3: Line 3:
<br>[[File:1771.png|500px|frameless|thumb]]<br>
<br>[[File:1771.png|500px|frameless|thumb]]<br>


<br>
==Introduction==
==Introduction==
keyestudio 4*4*4 RGB LED CUBE KIT consist of 64 RGB LEDs soldered in the combination of 4*4*4. It's then driven by ARDUINO. <br>
keyestudio 4*4*4 RGB LED CUBE KIT consist of 64 RGB LEDs soldered in the combination of 4*4*4. It's then driven by ARDUINO. RGB LED CUBE emits a warm light, which is enjoyable for people of any age. You can also use it as a mood light, or create your own "ambient device" that gently notifies you of new emails or instant 
RGB LED CUBE emits a warm light, which is enjoyable for people of any age. <br>
messages!  
You can also use it as a mood light, or create your own "ambient device" that gently notifies you of new emails or instant messages!  


<br>
The RGB LED CUBE KIT is supplied as a partly-assembled kit:<br>
The RGB LED CUBE KIT is supplied as a partly-assembled kit:<br>
The controller board is based on an Arduino-compatible 8*8 LED RGB Matrix driver board. All RGB LEDs are soldered to the plane PCB, and tested okay. You just need to solder and assemble the 3D matrix.<br>
The controller board is based on an Arduino-compatible 8*8 LED RGB Matrix driver board. <br>
All RGB LEDs are soldered to the plane PCB, and tested okay. You just need to solder and assemble the 3D matrix.<br>
 
The RGB LED CUBE KIT comes with a sketch pre-installed that runs through a test pattern.<br>
The RGB LED CUBE KIT comes with a sketch pre-installed that runs through a test pattern.<br>
You can also upload your own sketches using the Arduino IDE and the Cube4 library, which makes it easy for you to define your own animations and displays. For example, you could display:<br>


Weather conditions based on online weather service data<br>
For example, you could display:<br>
Heart beat animation driven by a heart rate monitor<br>
* Weather conditions based on online weather service data<br>
Colour animations synthronised to music<br>
* Heart beat animation driven by a heart rate monitor<br>
The water level in a water tank<br>
* Colour animations synthronised to music<br>
Whether your last software build passed or failed its tests<br>
* The water level in a water tank<br>
A visualisation of how much power your house is using<br>
* Whether your last software build passed or failed its tests<br>
Notifications for IM and email<br>
* A visualisation of how much power your house is using<br>
A visual count-down timer for some event<br>
* Notifications for IM and email<br>
* A visual count-down timer for some event<br>
 
<span style="color: red"> '''Note: the control board has a toggle switch, if connecting external DC 7-12V power, toggle switch must be set to Header terminal, or else it will burn out the control board; if set to Terminal terminal, external power only can accept 5V.'''
 
<br>


==Features==
==Features==
* 64 RGB LEDs<br>
* Simple assembly using a PCB frame<br>
* 8*8 LED RGB Matrix driver board (Arduino compatible)<br>
* 7-12V independent power supply<br>
* Arduino driver library with example programs<br>


• 64 RGB LEDs<br>
<br>
• Simple assembly using a PCB frame<br>
• 8*8 LED RGB Matrix driver board (Arduino compatible)<br>
• 7-12V independent power supply<br>
• Arduino driver library with example programs<br>
 
==Part list==
==Part list==
<br>[[File:1772.png|500px|frameless|thumb]]<br>
<br>[[File:1772.png|500px|frameless|thumb]]<br>
 
<br> [[File:1773.png|500px|frameless|thumb]]<br>
<br>[[File:1773.png|500px|frameless|thumb]]<br>
<br>
 
See the pic. above, and we list the cooresponding content below:<br>
1: controller 8*8 LED RGB Matrix driver board  (1 PCS)<br>
* 1: controller 8*8 LED RGB Matrix driver board  (1 PCS)<br>
2: soldering fixture (1 PCS)<br>
* 2: soldering fixture (1 PCS)<br>
3: top acrylic board (1 PCS)<br>
* 3: top acrylic board (1 PCS)<br>
4: bottom acrylic board (1 PCS)<br>
* 4: bottom acrylic board (1 PCS)<br>
5, 6, 7, 8: acrylic side boards, in which 5 and 7 is identical ( 4 in total)<br>
* 5, 6, 7, 8: acrylic side boards, in which 5 and 7 is identical ( 4 in total)<br>


<br>[[File:1774.png|500px|frameless|thumb]]<br>
<br>[[File:1774.png|500px|frameless|thumb]]<br>
See the pic. above, and we list the cooresponding content below:<br>
* 1: plane PCB strips with LEDs (16 PCS)<br>
* 2: holder bottom board(1 PCS)<br>
* 3: fixing strips for the PCB strips (8 PCS)<br>
* 4: copper bush (4 PCS)<br>
* 5: 16P header strips(2 PCS)<br>
* 6: 3*10 inner hexagon screw(4 PCS)<br>
* 7: 3M nut(4 PCS)<br>
* 8: holder stick (8 PCS)<br>
* 9: DC socket (1 PCS)<br>
* 10: 3*6 inner hexagon screw(8 PCS)<br>


1: plane PCB strips with LEDs (16 PCS)<br>
'''Self-prepared tools:''' Soldering iron and solder <br>
2: holder bottom board(1 PCS)<br>
3: fixing strips for the PCB strips (8 PCS)<br>
4: copper bush (4 PCS)<br>
5: 16P header strips(2 PCS)<br>
6: 3*10 inner hexagon screw(4 PCS)<br>
7: 3M nut(4 PCS)<br>
8: holder stick (8 PCS)<br>
9: DC socket (1 PCS)<br>
10: 3*6 inner hexagon screw(8 PCS)<br>
 
self-prepared tools: Soldering iron & solder<br>


<br>


Step by step soldering instructions:
== Step by step soldering instructions ==


  1. Bottom board soldering  
=== 1. Bottom board soldering ===


<br>[[File:1775.png|500px|frameless|thumb]]<br>
<br>[[File:1775.png|500px|frameless|thumb]]<br>
Line 70: Line 78:
Adjust the header strip for it to be vertical to the board, then solder it.  
Adjust the header strip for it to be vertical to the board, then solder it.  


2. Soldering of plane PCB strips with LEDs
<br>
=== 2. Soldering of plane PCB strips with LEDs ===


<br>[[File:1778.png|500px|frameless|thumb]]<br>
<br>[[File:1778.png|500px|frameless|thumb]]<br>
Line 96: Line 105:
Repeat the above steps to finish the other three.  
Repeat the above steps to finish the other three.  


3. Install the holder sticks
<br>
=== 3. Install the holder sticks ===
<br>[[File:17714.png|500px|frameless|thumb]]<br>
<br>[[File:17714.png|500px|frameless|thumb]]<br>


Line 133: Line 143:
Then add solder to the solder pads between the bottom board and the sticks. After all solder pads are soldered, check to see if there are areas left. Above is a pic. with soldering finished.  
Then add solder to the solder pads between the bottom board and the sticks. After all solder pads are soldered, check to see if there are areas left. Above is a pic. with soldering finished.  


4. Install the assembled parts  
<br>
=== 4. Install the assembled parts ===


<br>[[File:17723.png|500px|frameless|thumb]]<br>
<br>[[File:17723.png|500px|frameless|thumb]]<br>
Line 183: Line 194:
All installation finished!  
All installation finished!  


==Program==   
 
<br>
==Wiring Table==   
        
        
'''Wiring: wiring table'''
{| width="80%" cellspacing="0" border="1"
{| width="80%" cellspacing="0" border="1"
|-
|-
Line 215: Line 226:
|}
|}


'''Connection diagram'''  <br>
<br>
'''Note: the control board has a toggle switch, if connecting external DC 7-12V power, toggle switch must be set to Header terminal, or else it will burn out the control board; if set to Terminal terminal, external power only can accept 5V.'''


<br>[[File:g.png|500px|frameless|thumb]]<br>
== Connection diagram ==


'''Sample code'''
<span style="color: red"> '''Note: the control board has a toggle switch, if connecting external DC 7-12V power, toggle switch must be set to Header terminal, or else it will burn out the control board; if set to Terminal terminal, external power only can accept 5V.'''
 
<br>[[File:g.png|700px|frameless|thumb]]<br>
 
<br>
 
== Sample Code ==
<pre>
<pre>
#include <Colorduino.h>
#include <Colorduino.h>
Line 370: Line 386:
</pre>
</pre>


<br>
When uploading the code, remember to select the Board '''Arduino Pro/Pro Mini'''.
<br>[[File:0177-1.png|500px|frameless|thumb]]<br>
<br>[[File:0177-2.png|500px|frameless|thumb]]<br>


<br>
After program is uploaded, with power on , you can see the beautiful light effect.
<br>[[File:17736.png|500px|frameless|thumb]]<br>
<br>[[File:17736.png|500px|frameless|thumb]]<br>


After program is uploaded, with power on , you can see the beautiful light effect.
<br>


==Resources for the project==
==Resources for the project==
* '''ARDUINO software download address:''' <br>
https://www.arduino.cc/en/Main/Software<br>


'''ARDUINO software download address:''' <br>
* '''PDF And Library:''' <br>
https://www.arduino.cc/en/Main/Software<br>
https://fs.keyestudio.com/KS0177
'''Project library address:''' <br>
 
http://7326097.s21d-7.faiusrd.com/0/ABUIABAAGAAgopSduwUo7N7p8AQ?f=Colorduino.rar&v=1466386924<br>
* '''Installation video address:''' <br>
'''Installation video address:''' <br>
http://video.keyestudio.com/KS0177/ <br>
http://www.keyestudio.com/wp/2016/11/ks0177keyestudio-rgb-led-cube-kit/  <br>
 
'''For reference:''' <br>
* '''For reference:''' <br>
http://www.hownottoengineer.com/projects/rgb-led-cube.html<br>
http://www.hownottoengineer.com/projects/rgb-led-cube.html<br>
http://www.instructables.com/id/4x4x4-RGB-LED-Cube/
http://www.instructables.com/id/4x4x4-RGB-LED-Cube/


'''PDF:''' <br>
 
https://drive.google.com/open?id=1SuWaXFSmZL3tKuIpwb1F3JraJumBH_QP
<br>


== Get One Now ==
== Get One Now ==
'''Official Website'''
*[https://www.keyestudio.com/2018new-keyestudio-444-rgb-led-display-cube-starter-kit-for-arduino-projectrgb-driver-boardfdti-module-unassembled-p0132-p0132.html  '''Official Website''']
 
*[https://www.amazon.com/dp/B01JZ1QG8Oc  '''Shop on amazon''' ]


http://www.keyestudio.com/keyestudio-4-4-4-rgb-led-cube-light-kit-with-8-8-led-rgb-matrix-driver-board-for-arduino.html


[[Category:Starter Kit]]
[[Category:Starter Kit]]

Latest revision as of 13:57, 4 December 2019

keyestudio 4*4*4 RGB LED CUBE KIT


thumb


Introduction

keyestudio 4*4*4 RGB LED CUBE KIT consist of 64 RGB LEDs soldered in the combination of 4*4*4. It's then driven by ARDUINO. 
RGB LED CUBE emits a warm light, which is enjoyable for people of any age. 
You can also use it as a mood light, or create your own "ambient device" that gently notifies you of new emails or instant messages!


The RGB LED CUBE KIT is supplied as a partly-assembled kit:
The controller board is based on an Arduino-compatible 8*8 LED RGB Matrix driver board.
All RGB LEDs are soldered to the plane PCB, and tested okay. You just need to solder and assemble the 3D matrix.

The RGB LED CUBE KIT comes with a sketch pre-installed that runs through a test pattern.

For example, you could display:

  • Weather conditions based on online weather service data
  • Heart beat animation driven by a heart rate monitor
  • Colour animations synthronised to music
  • The water level in a water tank
  • Whether your last software build passed or failed its tests
  • A visualisation of how much power your house is using
  • Notifications for IM and email
  • A visual count-down timer for some event

Note: the control board has a toggle switch, if connecting external DC 7-12V power, toggle switch must be set to Header terminal, or else it will burn out the control board; if set to Terminal terminal, external power only can accept 5V.


Features

  • 64 RGB LEDs
  • Simple assembly using a PCB frame
  • 8*8 LED RGB Matrix driver board (Arduino compatible)
  • 7-12V independent power supply
  • Arduino driver library with example programs


Part list


thumb

thumb

See the pic. above, and we list the cooresponding content below:

  • 1: controller 8*8 LED RGB Matrix driver board (1 PCS)
  • 2: soldering fixture (1 PCS)
  • 3: top acrylic board (1 PCS)
  • 4: bottom acrylic board (1 PCS)
  • 5, 6, 7, 8: acrylic side boards, in which 5 and 7 is identical ( 4 in total)


thumb
See the pic. above, and we list the cooresponding content below:

  • 1: plane PCB strips with LEDs (16 PCS)
  • 2: holder bottom board(1 PCS)
  • 3: fixing strips for the PCB strips (8 PCS)
  • 4: copper bush (4 PCS)
  • 5: 16P header strips(2 PCS)
  • 6: 3*10 inner hexagon screw(4 PCS)
  • 7: 3M nut(4 PCS)
  • 8: holder stick (8 PCS)
  • 9: DC socket (1 PCS)
  • 10: 3*6 inner hexagon screw(8 PCS)

Self-prepared tools: Soldering iron and solder


Step by step soldering instructions

1. Bottom board soldering


thumb

Plug the two 16P header strips vertically onto the holes of the bottom board (the side with no keyestudio logo facing up as above pic. shows ) , then solder the pins.


thumb

Adjust the header strip for it to be vertical to the board, then solder it.


2. Soldering of plane PCB strips with LEDs


thumb

Disassemble the plane PCBs as above pic. shows.


thumb

Next, disassemble the fixing strips for the PCB strips.


thumb

Set the 4 copper bushes in standing position, place 4 plane PCB strips to the soldering fixture. The black lines on the plane PCBs are position indicators for latter soldering of fixing strips.


thumb

Place the soldering fixture on top of the 4 copper bushes, then place two fixing strips between the black indicator lines, then add solder to the 8 solder points for fixing.


thumb

Above is a pic. when you finish soldering of the 8 soldering points.


thumb

Repeat the above steps to finish the other three.


3. Install the holder sticks


thumb

Every holder stick has a dedicated position, so before installation, pls read this instruction for the positioning of each stick. As above pic. shows, stick A belongs to hole A of the bottom board, stick B belongs to hole B and etc. 8 sticks for 8 holes correspondingly.


thumb

As above picture, position the 4 soldered plane PCBs in a uniform direction. Install stick A on the recess area. And don’t solder just yet!


thumb

Repeat above step and install stick C, E and G.


thumb

Install stick B on the recess area. And don’t solder just yet!


thumb

Repeat the above step and install stick D, F, and H.


thumb

Plug the above assembled part into the bottom board.


thumb

After plugging in, adjust the assembled part and the bottom board for them to be in vertical position.


thumb

Next, add solder to the solder pad areas. For places where solder pads are only on the plane PCBs but not the sticks, they don’t need to be soldered.


thumb

Then add solder to the solder pads between the bottom board and the sticks. After all solder pads are soldered, check to see if there are areas left. Above is a pic. with soldering finished.


4. Install the assembled parts


thumb

Use 4 3*6 screws to fix the 4 copper bushes onto the acrylic bottom boards.


thumb

Next, fix the driver board onto the copper bushes using 3*6 screws in a direction as above pic.


thumb

Strip a Dupont wire, solder the copper wire to the driver board as above pic.


thumb

Install the DC socket to the acrylic side board 5, the direction as above picture.


thumb

Install the acrylic side board 5 to the bottom board. Then solder the copper wire, the one close to the screw to the shorter lead of the DC socket (positive end), the other copper wire solder to the longer lead (negative end).


thumb

Plug the header pins of the bottom board(direction as above pic.) to the female headers of VCC, GREEN, VCC of the driver board, pay attention not to reverse.


thumb

Place the other 3 side boards according to the shape of groove of the acrylic bottom board.


thumb

Place the top acrylic board according to the groove shape.


thumb

After installation of the top acrylic board, turn the part upside down, use two 3*10 screws and two 3M nuts to fix the side board.


thumb

A pic. after screws fixed.


thumb

Then, install the screws on the top acrylic board.


thumb

All installation finished!



Wiring Table

RGB Matrix driver board Arduino FTDI basic program downloader
VDD 5V
GND GND
DTR DTR
TXD RXD
RXD TXD


Connection diagram

Note: the control board has a toggle switch, if connecting external DC 7-12V power, toggle switch must be set to Header terminal, or else it will burn out the control board; if set to Terminal terminal, external power only can accept 5V.


thumb


Sample Code

#include <Colorduino.h>
typedef struct
{
unsigned char r;
unsigned char g;
unsigned char b;
} ColorRGB;
//a color with 3 components: h, s and v
typedef struct
{
unsigned char h;
unsigned char s;
unsigned char v;
} ColorHSV;
unsigned char plasma[ColorduinoScreenWidth][ColorduinoScreenHeight];
long paletteShift;
//Converts an HSV color to RGB color
/*void HSVtoRGB(void *vRGB, void *vHSV)  /////////////////////////////////////
{float r, g, b, h, s, v; //this function works with floats between 0 and 1
float f, p, q, t;
int i;
ColorRGB *colorRGB=(ColorRGB *)vRGB;
ColorHSV *colorHSV=(ColorHSV *)vHSV;
h = (float)(colorHSV->h / 256.0);
s = (float)(colorHSV->s / 256.0);
v = (float)(colorHSV->v / 256.0);
//if saturation is 0, the color is a shade of grey
if(s == 0.0) {
b = v;
g = b;
r = g;
}
//if saturation > 0, more complex calculations are needed
else
{
h *= 6.0; //to bring hue to a number between 0 and 6, better for the calculations
i = (int)(floor(h)); //e.g. 2.7 becomes 2 and 3.01 becomes 3 or 4.9999 becomes 4
f = h - i;//the fractional part of h
p = (float)(v * (1.0 - s));
q = (float)(v * (1.0 - (s * f)));
t = (float)(v * (1.0 - (s * (1.0 - f))));
switch(i)
{
case 0: r=v; g=t; b=p; break;
case 1: r=q; g=v; b=p; break;
case 2: r=p; g=v; b=t; break;
case 3: r=p; g=q; b=v; break;
case 4: r=t; g=p; b=v; break;
case 5: r=v; g=p; b=q; break;
default: r = g = b = 0; break;
}
}
colorRGB->r = (int)(r * 255.0);
colorRGB->g = (int)(g * 255.0);
colorRGB->b = (int)(b * 255.0);
}
float dist(float a, float b, float c, float d)///////////////////////////////////////////////////////
{
return sqrt((c-a)*(c-a)+(d-b)*(d-b));
}
void plasma_morph()                    //////////////////////////////////////////////
{
unsigned char x,y;
float value;
ColorRGB colorRGB;
ColorHSV colorHSV;
for(y = 0; y < ColorduinoScreenHeight; y++)
for(x = 0; x < ColorduinoScreenWidth; x++) {
{
value = sin(dist(x + paletteShift, y, 128.0, 128.0) / 8.0)
+ sin(dist(x, y, 64.0, 64.0) / 8.0)
+ sin(dist(x, y + paletteShift / 7, 192.0, 64) / 7.0)
+ sin(dist(x, y, 192.0, 100.0) / 8.0);
colorHSV.h=(unsigned char)((value) * 128)&0xff;
colorHSV.s=255;
colorHSV.v=255;
HSVtoRGB(&colorRGB, &colorHSV);
Colorduino.SetPixel(x, y, colorRGB.r, colorRGB.g, colorRGB.b);
}
}
paletteShift++;
Colorduino.FlipPage(); // swap screen buffers to show it
}*/
/********************************************************
Name: ColorFill
Function: Fill the frame with a color
Parameter:R: the value of RED. Range:RED 0~255
G: the value of GREEN. Range:RED 0~255
B: the value of BLUE. Range:RED 0~255
********************************************************/
void ColorFill(unsigned char R,unsigned char G,unsigned char B)
{
PixelRGB *p = Colorduino.GetPixel(0,0);
for (unsigned char y=0;y<ColorduinoScreenWidth;y++) {
for(unsigned char x=0;x<ColorduinoScreenHeight;x++) {
p->r = R;
p->g = G;
p->b = B;
p++;
}
}
Colorduino.FlipPage();
}
void setup()
{
Colorduino.Init(); // initialize the board
// compensate for relative intensity differences in R/G/B brightness
// array of 6-bit base values for RGB (0~63)
// whiteBalVal[0]=red
// whiteBalVal[1]=green
// whiteBalVal[2]=blue
//http://keyes-arduino.taobao.com
unsigned char whiteBalVal[3] = {36,63,63}; // for LEDSEE 6x6cm round matrix
Colorduino.SetWhiteBal(whiteBalVal);
// start with morphing plasma, but allow going to color cycling if desired.
paletteShift=128000;
unsigned char bcolor;
//generate the plasma once
/*for(unsigned char y = 0; y < ColorduinoScreenHeight; y++)
for(unsigned char x = 0; x < ColorduinoScreenWidth; x++)
{
//the plasma buffer is a sum of sines
bcolor = (unsigned char)
(
128.0 + (128.0 * sin(x*8.0 / 16.0))
+ 128.0 + (128.0 * sin(y*8.0 / 16.0))
) / 2;
plasma[x][y] = bcolor;
}*/
// to adjust white balance you can uncomment this line
// and comment out the plasma_morph() in loop()
// and then experiment with whiteBalVal above
 ColorFill(0,0,0);
}
void loop()
{
//plasma_morph();
 ColorFill(255,0,0);
 delay(2000);
 ColorFill(0,255,0);
 delay(2000); 
 ColorFill(0,0,255);
 delay(2000);
// ColorFill(255,255,255);
// delay(1000);
}


When uploading the code, remember to select the Board Arduino Pro/Pro Mini.
thumb

thumb


After program is uploaded, with power on , you can see the beautiful light effect.
thumb


Resources for the project

  • ARDUINO software download address:

https://www.arduino.cc/en/Main/Software

  • PDF And Library:

https://fs.keyestudio.com/KS0177

  • Installation video address:

http://video.keyestudio.com/KS0177/

  • For reference:

http://www.hownottoengineer.com/projects/rgb-led-cube.html
http://www.instructables.com/id/4x4x4-RGB-LED-Cube/



Get One Now