Ks0192 keyestudio 4WD Bluetooth Multi-functional Car

From Keyestudio Wiki
Revision as of 16:31, 20 September 2017 by Keyestudio (talk | contribs) (→‎Resources)
Jump to navigation Jump to search

keyestudio 4WD Bluetooth Multi-functional Car


thumb

Introduction

keyestudio 4WD Bluetooth Multi-functional Car is a learning application development system based on microcontroller and with ATmega-328 as core. It has functions of line tracking, obstacle avoidance, IR remote control , Bluetooth remote control and detecting distance. This kit contains plenty of interesting programs and can extend an external circuit module to increase more functions of this car. The kit aims to disengage users from boring theories and obtain capacity of system development when they are learning Arduino.

Parameters

1.Motor: Voltage: 6-9V Reduction Ratio: 1:48
2.Choosing L298N driver module as control motor, separated from microcontrollor
3.Three line tracking modules, having higher precision when detecting white and black lines,able to realize anti-falling
4.IR remote control module making up a remote control system of the car
5.Using ultrasonic module to realize obstacle avoidance
6.Pairing mobile phone Bluetooth with Bluetooth remote control module to control the car
7.Able to connect with external voltage at 7~12V,and equip with various sensors to complete different functions as much as possible

Component List

No. Product Name Quantity Picture
1 keyestudio UNO R3 1
thumb
2 keyestudio Shield V5 1
thumb
3 keyestudio L298N Motor Shield 1
thumb
4 keyestudio Bluetooh HC-06 1
thumb
5 I2C 1602 LCD 1
thumb
6 keyestudio Line Tracking Sensor 3
thumb
7 HC-SR04 Ultrasonic Sensor 1
thumb
8 keyestudio Digital IR Receiver Module 1
thumb
9 4WD Top PCB 1
thumb
10 4WD Bottom PCB 1
thumb
11 Servo Motor 1
thumb
12 Servo Plastic Platform 1
thumb
13 Remote Control of Chip 1
thumb
14 Toggle Switch + Wire 1 thumb
15 18650 Battery Case 1 thumb
16 Mental Motor 4 thumbthumbthumbthumb
17 Motor Fixed Part 4 thumbthumbthumbthumb
18 Plastic Tire 4 thumbthumbthumbthumb
19 Copper Pillar 35MM 6
thumb
20 Copper Pillar 20MM 3
thumb
21 Copper Pillar 6MM 6 thumbthumbthumbthumbthumbthumb
22 USB Cable 1
thumb
23 Dupont Line 30
thumb
24 M3*6MM Round Head Screw 60
thumb
25 M3*6MM Flat Head Screw 2 thumbthumb
26 M3*30MM Round Head Screw 8 thumbthumbthumbthumbthumbthumbthumbthumb
27 3MM Nut 16
thumb
28 Connector Wire (150mm, Black) 6
thumb
29 Connector Wire (150mm, Red) 6
thumb
30 Winding Wire (12CM) 1
thumb

Project List

Project 1:Line Tracking Sensor
Project 2:Ultrasonic Sensor
Project 3: Digital IR Receiver Module
  Project 4: Servo Motor
Project 5: Bluetooth Module
Project 6: L298N Motor Driver
Project 7: I2C 1602 LCD
Project 8:Line Tracking of Smart Car
Project 9:Obstacle Avoidance of Smart Car
Project 10:IR Remote Control of Smart Car
Project 11:Distance Detecting of Smart Car
Project 12:Bluetooth Remote Control of Smart Car
Project 13:5 in 1 Muilti-functional Car

Address of Assembly Video

http://www.keyestudio.com/wp/2016/09/ks0192

Address of Demonstration Video

http://www.keyestudio.com/wp/2016/09/ks0192-keyestudio-4wd-bluetooth-multi-functional-car-demonstration-video/


Project Details

Project 1:Line Tracking Sensor


thumb

Introduction:

This Line Tracking Sensor can detect white lines in black and black lines in white. The single line-tracking signal provides a stable output signal TTL for a more accurate and more stable line. Multi-channel option can be easily achieved by installing required line-tracking robot sensors.

Specification:

Power Supply: +5V
Operating Current: <10mA
Operating Temperature Range: 0°C ~ + 50°C
Output Interface: 3-wire interface (1 - signal, 2 - power, 3 - power supply negative)
Output Level: TTL level

Connection Diagram:


thumb


Sample Code:

const int sensorPin = 3;     // the number of the sensor pin
const int ledPin =  13;      // the number of the LED pin
int sensorState = 0;         // variable for reading the sensor status
void setup() {
  pinMode(ledPin, OUTPUT);      
  pinMode(sensorPin, INPUT); }
void loop(){
  // read the state of the sensor value:
  sensorState = digitalRead(sensorPin);
  // if the sensorState is HIGH:
  if (sensorState == HIGH) {     
     digitalWrite(ledPin, HIGH);  
  } 
  else {digitalWrite(ledPin, LOW); 
  }}

Result

After power-on, power indicator D1 is on. When you block the sensing part of line tracking sensor with black paper, LED on the sensor is off as shown in Figure 1. When you block it with white paper, LED is on as shown in Figure 2.

Figure 1


thumb

Figure 2


thumb

Project 2: Ultrasonic Sensor


thumb

Introduction:
  The HC-SR04 Ultrasonic Sensor is a very affordable proximity/distance sensor that has been used mainly for object avoidance in various robotics projects. It essentially gives your Arduino eyes / spacial awareness and can prevent your robot from crashing or falling off a table. It has also been used in turret applications, water level sensing, and even as a parking sensor. This simple project will use the HC-SR04 sensor with an Arduino and a Processing sketch to provide a neat little interactive display on your computer screen.

Specification:

Working Voltage: DC 5V
Working Current: 15mA
Working Frequency: 40Hz
Max Range: 4m
Min Range: 2cm
Measuring Angle: 15 degree
Trigger Input Signal: 10µS TTL pulse
Echo Output Signal Input TTL lever signal and the range in proportion
Size: 46*20.4mm
Weight: 9g

Connection Diagram:


thumb


thumb

Sample Code:

VCC to arduino 5v
GND to arduino GND
Echo to Arduino pin 7
Trig to Arduino pin 8

 
#define echoPin 7 // Echo Pin
#define trigPin 8 // Trigger Pin
#define LEDPin 13 // Onboard LED

int maximumRange = 200; // Maximum range needed
int minimumRange = 0; // Minimum range needed
long duration, distance; // Duration used to calculate distance

void setup() {
 Serial.begin (9600);
 pinMode(trigPin, OUTPUT);
 pinMode(echoPin, INPUT);
 pinMode(LEDPin, OUTPUT); // Use LED indicator (if required)
}

void loop() {
/* The following trigPin/echoPin cycle is used to determine the
 distance of the nearest object by bouncing soundwaves off of it. */ 
 digitalWrite(trigPin, LOW); 
 delayMicroseconds(2); 

 digitalWrite(trigPin, HIGH);
 delayMicroseconds(10); 
 digitalWrite(trigPin, LOW);
 duration = pulseIn(echoPin, HIGH);
 
 //Calculate the distance (in cm) based on the speed of sound.
 distance = duration/58.2;
 
 if (distance >= maximumRange || distance <= minimumRange){
 /* Send a negative number to computer and Turn LED ON 
 to indicate "out of range" */
 Serial.println("-1");
 digitalWrite(LEDPin, HIGH); 
 }
 else {
 /* Send the distance to the computer using Serial protocol, and
 turn LED OFF to indicate successful reading. */
 Serial.println(distance);
 digitalWrite(LEDPin, LOW); 
 } 
 //Delay 50ms before next reading.
 delay(50);
}

Result

After connection and uploading, when ultrasonic sensor senses obstacle within sensing area, it is measuring the distance between itself and obstacle and the value of distance is displayed on serial monitor as shown in bellow figure.


thumb

Project 3: Digital IR Receiver Module


thumb

Introduction:

IR is widely used in remote control. With this IR receiver, Arduino project is able to receive command from any IR remoter controller if you have the right decoder. Well, it will be also easy to make your own IR controller using IR transmitter.

Specification:

Power Supply: 5V
Interface: Digital
Modulate Frequency: 38Khz
Module Interface Socket: JST PH2.0

NOTE: In the sample code below Digital pin 11 is in use, you may either change your wiring or change the sample code to match. 

Connection Diagram: 


thumb


Sample Code:

#include <IRremote.h>
 int RECV_PIN = 11;
 IRrecv irrecv(RECV_PIN);
 decode_results results;
 void setup()
{
  Serial.begin(9600);
  irrecv.enableIRIn(); // Start the receiver
}
 void loop() {
  if (irrecv.decode(&results)) {
    Serial.println(results.value, HEX);
    irrecv.resume(); // Receive the next value
  }
}

IR Remote Library includes some sample codes for sending and receiving.

https://github.com/shirriff/Arduino-IRremote


Result

In this project, we need to use a IR remote control which has 17 functional key and its launching distance is 8 meters at most, proper to control various devices indoors. This project is actually to decode remote control signal. After connection and uploading codes, aim at IR receiving module and press the key, finally you can see corresponding codes. If you press the key too long, it will show messy codes easily as shown in bellow figure.


thumb


thumb

Project 4: Servo Motor


thumb

Introduction

Servomotor is a position control rotary actuator. It mainly consists of housing, circuit board, core-less motor, gear and position sensor. The receiver or MCU outputs a signal to the servomotor. The motor has a  built-in reference circuit that gives out reference signal, cycle of 20ms and width of 1.5ms. The motor compares the acquired DC bias voltage to the voltage of the potentiometer and outputs a voltage difference. The IC on the circuit board will decide the rotate direction accordingly and drive the core-less motor. The gear then pass the force to the shaft. The sensor will determine if it has reached the commanded position according to the feedback signal. Servomotors are used in control systems that requires to have and maintain different angles. When the motor speed is definite, the gear will  cause the potentiometer to  rotate. When the voltage difference reduces to zero, the motor stops. Normally, the rotation angle range is among 0-180 degrees.

Servomotor comes with many specifications. But all of them have three connection wires, distinguished by brown, red, orange colors(different brand may have different color). Brown one is for GND, red one for power positive, orange one for signal Line.


thumb

The rotate angle of the servo motor is controlled by regulating the duty cycle of the PWM(Pulse-Width Modulation) signal. The standard cycle of the PWM signal is 20ms(50Hz). Theoretically, the width is distributed between 1ms-2ms, but in fact, it's between 0.5ms-2.5ms. The width corresponds the rotate angle from 0° to 180°. But note that for different brand motor, the same signal may have different rotate angle. 


thumb

After some basic knowledge, let's learn how to control a servomotor. For this experiment, you only need a servomotor and several jumper wires. 

Connection & Sample Program
There are two ways to control a servomotor with Arduino. One is to use a common digital sensor port of Arduino to produce square wave with different duty cycle to simulate PWM signal and use that signal to control the positioning of the motor. Another way is to directly use the Servo function of the Arduino to control the motor. In this way, the program will be easier but it can only control two-contact motor because for the servo function, only digital pin 9 ang 10 can be used. The Arduino drive capacity is limited. So if you need to control more than one motor, you will need external power.

Connection Diagram:


thumb

Sample Code:

int servopin=9;// select digital pin 9 for servomotor signal line
int myangle;// initialize angle variable
int pulsewidth;// initialize width variable
int val;
void servopulse(int servopin,int myangle)// define a servo pulse function
{
pulsewidth=(myangle*11)+500;// convert angle to 500-2480 pulse width
digitalWrite(servopin,HIGH);// set the level of servo pin as “high”
delayMicroseconds(pulsewidth);// delay microsecond of pulse width
digitalWrite(servopin,LOW);// set the level of servo pin as “low”
delay(20-pulsewidth/1000);
}
void setup()
{
pinMode(servopin,OUTPUT);// set servo pin as “output”
Serial.begin(9600);// connect to serial port, set baud rate at “9600”
Serial.println("servo=o_seral_simple ready" ) ;
}
void loop()// convert number 0 to 9 to corresponding 0-180 degree angle, LED blinks corresponding number of time
{
val=Serial.read();// read serial port value
if(val>'0'&&val<='9')
{
val=val-'0';// convert characteristic quantity to numerical variable
val=val*(180/9);// convert number to angle
Serial.print("moving servo to ");
Serial.print(val,DEC);
Serial.println();
for(int i=0;i<=50;i++) // giving the servo time to rotate to commanded position
{
servopulse(servopin,val);// use the pulse function
}
}
}

Result

When you input a number on serial monitor, the motor rotates to an angle which is equal to the number input, and the angle dimension will be displayed on screen, as shown in bellow figure.


thumb

Project 5: Bluetooth Module


thumb

Introduction:

This Bluetooth module can easily achieve serial wireless data transmission. Its operating frequency is among the most popular 2.4GHz ISM frequency band (i.e. Industrial, scientific and medical). It adopts Bluetooth 2.1+EDR standard. In Bluetooth 2.1, signal transmit time of different devices stands at a 0.5 seconds interval so that the workload of bluetooth chip can be reduced substantially and more sleeping time can be saved for bluetooth. This module is set with serial interface, which is easy-to-use and simplifying overall design/development cycle.

Specification:

Bluetooth Protocol: Bluetooth 2.1+ EDR Standard
USB Protocol: USB v1.1/2.0
Operating Frequency: 2.4GHz ISM Frequency Band
Modulation Mode: Gauss Frequency Shift Keying
Transmit Power: ≤ 4dBm, Second Stage
Sensitivity: ≤-84dBm at 0.1% Bit Error Rate
Transmission Speed: 2.1Mbps(Max)/160 kbps(Asynchronous); 1Mbps/1Mbps(Synchronous)
Safety Feature: Authentication and Encryption
Supported Configuration: Bluetooth Serial Port (major and minor)
Supply Voltage: +3.3 VDC 50mA
Operating Temperature: -20 to 55℃

Connection Diagram:

br>thumb

Sample Code:

int val; 
int ledpin=13; 
void setup() 
{ 
Serial.begin(9600);
 pinMode(ledpin,OUTPUT); 
} void loop()
{ val=Serial.read(); 
if(val=='a')
 { 
digitalWrite(ledpin,HIGH); 
delay(250); 
digitalWrite(ledpin,LOW); 
delay(250);
 Serial.println("keyestudio");

Result

After power-on, power indicator D1 is on, and LED on Bluetooth module is blinking; open Bluetooth on mobile phone, pair them, input 1234, and finish pairing as shown in Figure 1 ; open APP—Bluetooth serial communication assistant, connect it to Bluetooth, select normal mode, complete connection, and LED on Bluetooth module is on as shown in Figure 2; input an “a” in the assistant, and display “keyesdudio” in it as shown in Figure 3.

Figure 1
thumb

Figure 2
thumb

Figure 3
thumb

Project 6: L298N Motor Driver


thumb

Introduction:

Using L298N made by ST Company as the control chip, the module has characteristics of strong driving ability, low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part. But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

Using large capacity filter capacitor, this module can follow current to protect diodes, and improve reliability.

Specification:

Working Mode: H bridge (double lines)
Control Chip: L298N (ST)
Logical Voltage: 5V
Driving Voltage: 5V-35V
Logical Current: 0mA-36mA
Driving Current: 2A (MAX single bridge)
Storage Temperature: (-20 °C)-(+135 °C)
Maximum Power: 25W
Weight: 30g
Periphery Dimension: 43 x 43 x 27 mm(L x W x H)


Circuit Connection:


thumb

thumb

Sample Code:

int IN2=6;
int IN3=7;
int IN4=8;
int ENA=9;
int ENB=10;
void setup()
{
for (int i = 5; i <11; i ++)
  {
    pinMode(i, OUTPUT);  
  }
}
void loop()
{
  // rotate CW
 digitalWrite(IN1,LOW);
 digitalWrite(IN2,HIGH);
analogWrite(ENA,200);
 digitalWrite(IN3,LOW);
 digitalWrite(IN4,HIGH);
analogWrite(ENB,200);
 delay(1000);
 // pause for 1S
 analogWrite(ENA,0);
analogWrite(ENB,0);
 delay(1000);
 // rotate CCW
 digitalWrite(IN1,HIGH);
 digitalWrite(IN2,LOW);
 analogWrite(ENA,100);
 digitalWrite(IN3,HIGH);
 digitalWrite(IN4,LOW);
analogWrite(ENB,100);
 delay(1000);
 // pause for 1S
 analogWrite(ENA,0);
analogWrite(ENB,0);
 delay(1000);
}


Result

After connection and power-on, two motors rotate clockwise for 1 second at a speed of 200 (PWM value is 200) and then stop for 1 second; two motors rotate anticlockwise for 1 second at a speed of 100 (PWM value is 100) and then stop for 1 second; circulating like this.

Project 7:keyestudio 1602 I2C Module


thumb


thumb

Introduction:

This is great LCD display compatible with arduino. With limited pin resources, your project will quickly run out of resources using normal LCDs. With this I2C interface LCD module, you only need 2 lines (I2C)to display the information.If you already have I2C devices in your project, this LCD module actually cost no more resources at all. The address can be set 0x27.

Specification:

I2C Address: 0x27
Back Lit (Blue with white char color)
Supply Voltage: 5V
Interface:I2C/TWI x1,Gadgeteer interface x2
Adjustable Contrast
Size:82x35x18 mm

Connection Diagram:

I602 is equipped with 4 pins in total. SCL should be connected to analog 5, SDA to analog 4, VCC to +5V and GND to ground.

Connection :


thumb

Sample Code:

//Compatible with the Arduino IDE 1.0
//Library version:1.1
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,16,2); // set the LCD address to 0x27 for a 16 chars and 2 line display
void setup()
{
lcd.init(); // initialize the lcd
lcd.init();
// Print a message to the LCD.
lcd.backlight();
lcd.setCursor(3,0);
lcd.print("Hello, world!");
lcd.setCursor(2,1);
lcd.print("keyestudio!");
}
void loop()
{}

Get libraries of Wire and LiquidCrystal_I2C from :

http://www.keyestudio.com/files/index/download/id/1479115840/

Result

After connection and uploading codes, the result of keyestudio 1602 I2C Module will be displayed as shown in bellow figure.


thumb

Project 8: Line Tracking of Smart Car


thumb

Introduction:

This project introduces a simple and automatic line tracking system of a car based on Arduino microcontroller.This car ,regarding UNO as main control, detect black line by IR photoelectric sensor and send the feedback to Arduino. Arduino will analyses the feedback signal and then control the driver motor to adjust the car diversion. Finally the car is able to go around the black line automatically. In addition, you can observe the state of the car through keyestudio 1602 I2C Module.

Principle:

1.Black absorbs most light. When the plane isn’t black, most IR emitted by the sensor is reflected back. So the sensor output low level at 0.
2.When there is a sensor above black line, since reflectivity of black is small ,little IR is reflected back under demand that the sensor works. Therefore, the sensor output 1.
3.We just need to know the output of the sensor is 1 or 0 with Arduino to detect black line.
4.Arduino control the motion of the car according to receiving signal. The system scheme is showed by following picture 1-1.


thumb

5.The system is composed of main control circuit, power supply, IR detecting module ,motor and driver module. The structure chart of the system is showed by picture 2-1.


thumb

Schematic Diagram:


thumb

Connection Diagram:


thumb

Sample Code:

#include <LiquidCrystal_I2C.h> 
#include <Wire.h> 
#define SensorLeft    6   //input pin of left sensor
#define SensorMiddle  9   //input pin of middle sensor
#define SensorRight   11   //input pin of right sensor
unsigned char SL;        //state of left sensor
unsigned char SM;        //state of middle sensor
unsigned char SR;        //state of right sensor
#define Lpwm_pin  5     //pin of controlling speed---- ENA of motor driver board
#define Rpwm_pin  10    //pin of controlling speed---- ENA of motor driver board
int pinLB=2;            //pin of controlling diversion----IN1 of motor driver board
int pinLF=4;            //pin of controlling diversion----IN2 of motor driver board
int pinRB=7;            //pin of controlling diversion----IN3 of motor driver board
int pinRF=8;            //pin of controlling diversion----IN4 of motor driver board
unsigned char Lpwm_val =180;//the speed of left wheel at 180 in initialization
unsigned char Rpwm_val = 180;//the speed of right wheel at 180 in initialization
int Car_state=0;             //state of car moving
LiquidCrystal_I2C lcd(0x27,16,2);  // set the LCD address to 0x27 for a 16 chars and 2 
void LCD1602_init(void)
{
  lcd.init();                     
  lcd.backlight(); 
  lcd.clear();  
}
void Sensor_IO_Config()
{
  pinMode(SensorLeft,INPUT);
  pinMode(SensorMiddle,INPUT);
  pinMode(SensorRight,INPUT);
}
void Sensor_Scan(void)
{
  SL = digitalRead(SensorLeft);
  SM = digitalRead(SensorMiddle);
  SR = digitalRead(SensorRight);
}
void M_Control_IO_config(void)//initialized function of IO of motor driver
{
  pinMode(pinLB,OUTPUT); // pin 2--IN1 of motor driver board
  pinMode(pinLF,OUTPUT); // pin 4--IN2 of motor driver board
  pinMode(pinRB,OUTPUT); // pin 7--IN3 of motor driver board
  pinMode(pinRF,OUTPUT); // pin 8--IN4 of motor driver board
  pinMode(Lpwm_pin,OUTPUT); // pin 5  (PWM) --ENA of motor driver board
  pinMode(Rpwm_pin,OUTPUT); // pin 10 (PWM) --ENB of motor driver board  
}
void Set_Speed(unsigned char Left,unsigned char Right)//setting function of speed
{
  analogWrite(Lpwm_pin,Left);   
  analogWrite(Rpwm_pin,Right);
}
void advance()     // going forwards
    {
     digitalWrite(pinRB,LOW);  // making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,LOW);  //  making motor move towards left rear
     digitalWrite(pinLF,HIGH); 
     Car_state = 1; 
     show_state();   
    }
void turnR()        //turning on the right(dual wheels)
    {
     digitalWrite(pinRB,LOW);  //making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,LOW);  //making motor move towards left front
     Car_state = 4;
     show_state();
    }
void turnL()        //turning on the left(dual wheels)
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,LOW );   //making motor move towards right front
     digitalWrite(pinLB,LOW);   //making motor move towards left rear
     digitalWrite(pinLF,HIGH);
     Car_state = 3;
     show_state();
    }    
void stopp()         //stop
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,HIGH);
     Car_state = 5;
     show_state();
    }
void back()          //back
    {
     digitalWrite(pinRB,HIGH);  //making motor move towards right rear
     digitalWrite(pinRF,LOW);
     digitalWrite(pinLB,HIGH);  //making motor move towards left rear
     digitalWrite(pinLF,LOW);
     Car_state = 2;
     show_state() ;    
    }
void show_state(void)  //showing current state of the car
{
  lcd.setCursor(0, 1); //showing from second row
   switch(Car_state)
   {
     case 1:lcd.print(" Go  ");Serial.print("\n GO");
     break;
     case 2:lcd.print("Back ");Serial.print("\n Back");
     break;
     case 3:lcd.print("Left ");Serial.print("\n Left");
     break;
     case 4:lcd.print("Right");Serial.print("\n Right");
     break;
     case 5:lcd.print("Stop ");Serial.print("\n Stop"); 
     break;
     default:
     break;
   }
}
void setup() 
{ 
   LCD1602_init();
   Sensor_IO_Config();
   M_Control_IO_config();        //motor controlling the initialization of IO
   Set_Speed(Lpwm_val,Rpwm_val); //setting initialization of speed
   lcd.clear();
   lcd.setCursor(0, 0);  //cursor set in first row and first column,
   lcd.print("  Wait  Signal  ");
   stopp();
} 
unsigned char old_SL,old_SM,old_SR;
void loop() 
{ 
  Sensor_Scan();
 if (SM == HIGH)// middle sensor in black area
{
if (SL == LOW & SR == HIGH) // black on left, white on right, turn left
{
turnR();
}
else if (SR == LOW & SL == HIGH) // white on left, black on right, turn right
{
turnL();
}
else // white on both sides, going forward
{
advance();
}
}
else // middle sensor on white area
{
if (SL== LOW & SR == HIGH)// black on left, white on right, turn left
{
turnR();
}
else if (SR == LOW & SL == HIGH) // white on left, black on right, turn right
{
turnL();
}
else // all white, stop
{
back();
delay(100);
stopp() ; 
}
}
} 

Project 9: Ultraviolet Obstacle Avoidance of Smart Car


thumb

Introduction:

This project ,regarding Arduino UNO as main control, detect front obstacle by ultrasonic sensor and platform motor, and send the feedback to Arduino. Arduino will analyses the feedback signal and then control the driver motor to adjust the car diversion. Finally the car is able to avoid obstacle automatically and keep going.

Principle:

1.Ultrasonic detecting distance: one port emits high level more than 10 US. Once it outputting level, open potentiometer to time. When the port becomes low level, read out current value. Use the time of detecting distance to calculate distance.
2.Use ultrasonic to detect the distance between obstacle and car, so that control the motion of the car according to the data.
3. If the distance between the car and obstacle is less than 20 cm, the car goes backward; if the distance is no less than 40 cm, the car goes forwards; if the distance is less than 40cm , the motor turns to detect the distance between car and left obstacle or right obstacle; if the distance between car and left obstacle, the distance between car and right obstacle are less than 15 cm, the car goes backward; if the distance between car and left obstacle is larger , the car turns left; if the distance between car and left obstacle is less than or equal to the distance between car and right obstacle, the car turns right.


Schematic Diagram:


thumb

Connection Diagram:


thumb

Sample Code:


#include <Servo.h> 
int pinLB = 2;     // defining pin 12
int pinLF = 4;     // defining pin 3 
int pinRB = 7;    // defining pin 13 
int pinRF = 8;    // defining pin 11 
int Lpwm_pin = 5;  //adjusting speed 
int Rpwm_pin = 10;   //adjusting speed //
unsigned char Lpwm_val = 200;
unsigned char Rpwm_val = 200;

int inputPin = A0;    // defining receiving pin of ultrasonic signal
int outputPin =A1;    // defining emitting pin of ultrasonic signal

int Fspeedd = 0;      // forward speed
int Rspeedd = 0;      // right speed
int Lspeedd = 0;      // left speed
int directionn = 0;   // front=8 back=2 left=4 right=6 
Servo myservo;        // setting myservo
int delay_time = 250; // time for servo motor turning backward

int Fgo = 8;         // going forward
int Rgo = 6;         // turning right
int Lgo = 4;         // turning left
int Bgo = 2;         // turning backward

void setup()
 {
  Serial.begin(9600);     // defining output pin of motor 
  pinMode(pinLB,OUTPUT); // pin 12
  pinMode(pinLF,OUTPUT); // pin 3 (PWM)
  pinMode(pinRB,OUTPUT); // pin 13
  pinMode(pinRF,OUTPUT); // pin 11 (PWM) 
  pinMode(inputPin, INPUT);    // defining input pin of ultrasonic
  pinMode(outputPin, OUTPUT);  // defining output pin of ultrasonic   
  myservo.attach(3);    // defining output pin9 of motor
 }
void advance()     // going forward
    { 
    digitalWrite(pinLB,LOW);    // right wheel going forward
    digitalWrite(pinRB, LOW);  // left wheel going forward
    digitalWrite(pinLF,HIGH);   
    digitalWrite(pinRF,HIGH);
    }
void stopp()         //stop
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,HIGH);
    }
void right()        //turning right(single wheel)
    {
  
     digitalWrite(pinRB,LOW);  //making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,LOW);  //making motor move towards left front
    }
void left()         //turning left(single wheel)
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,LOW );   //making motor move towards right front
     digitalWrite(pinLB,LOW);   //making motor move towards left rear
     digitalWrite(pinLF,HIGH);
    }
  
void back()          //going backward
    {
     digitalWrite(pinRB,HIGH);  //making motor move towards right rear
     digitalWrite(pinRF,LOW);
     digitalWrite(pinLB,HIGH);  //making motor move towards left rear
     digitalWrite(pinLF,LOW);  
    }
void detection()        //measuring 3 angles(0.90.179)
    {      
      int delay_time = 250;   // time for servo motor turning backward
      ask_pin_F();            // reading out the front distance
     if(Fspeedd < 20)         // assuming the front distance less than 10cm
      {
      stopp();               // clear output material
      delay(100);
      back();                // going backward for 0.2 second
      delay(200);
      }
           
      if(Fspeedd < 40)         // assuming the front distance less than 25cm
      {
        stopp();  
        delay(100);             // clear output material 
        ask_pin_L();            // reading out the left distance
        delay(delay_time);      // waiting servo motor to be stable
        ask_pin_R();            // reading out the right distance  
        delay(delay_time);      // waiting servo motor to be stable  
        
        if(Lspeedd > Rspeedd)   //assuming left distance more than  right distance
        {
          directionn = Lgo;      //turning left
        }
        
        if(Lspeedd <= Rspeedd)   //assuming left distance less than or equal to right distance
        {
         directionn = Rgo;      //turning right
        } 
        
        if (Lspeedd < 15 && Rspeedd < 15)   //assuming both left distance and right distance less than  10cm
        {
         directionn = Bgo;      //going backward        
        }          
      }
      else                      //assuming the front distance  more than 25 cm   
      {
        directionn = Fgo;        //going forward     
      }
     
    }    
void ask_pin_F()   // measuring the front distance 
    {
      myservo.write(90);
      digitalWrite(outputPin, LOW);   // ultrasonic launching low voltage at 2μs
      delayMicroseconds(2);
      digitalWrite(outputPin, HIGH);  // ultrasonic launching high voltage at 10μs,at least at10μs
      delayMicroseconds(10);
      digitalWrite(outputPin, LOW);    // keeping ultrasonic launching low voltage
      float Fdistance = pulseIn(inputPin, HIGH);  // time of error reading
      Fdistance= Fdistance/5.8/10;       // converting time into distance(unit:cm) 
      Fspeedd = Fdistance;              // reading-in Fspeedd(fore speed) with distance
    }  
 void ask_pin_L()   // measuring left distance 
    {
      myservo.write(5);
      delay(delay_time);
      digitalWrite(outputPin, LOW);   // ultrasonic launching low voltage at 2μs
      delayMicroseconds(2);
      digitalWrite(outputPin, HIGH);  // ultrasonic launching high voltage at 10μs,at least at10μs
      delayMicroseconds(10);
      digitalWrite(outputPin, LOW);    // keeping ultrasonic launching low voltage
      float Ldistance = pulseIn(inputPin, HIGH);  // time of error reading
      Ldistance= Ldistance/5.8/10;       // converting time into distance(unit:cm)
      Lspeedd = Ldistance;              //reading-in Lspeedd(left speed) with distance 
    }  
void ask_pin_R()   // measuring right distance 
    {
      myservo.write(177);
      delay(delay_time);
      digitalWrite(outputPin, LOW);   // ultrasonic launching low voltage at 2μs
      delayMicroseconds(2);
      digitalWrite(outputPin, HIGH);  // ultrasonic launching high voltage at 10μs,at least at10μs
      delayMicroseconds(10);
      digitalWrite(outputPin, LOW);    // keeping ultrasonic launching low voltage
      float Rdistance = pulseIn(inputPin, HIGH);  // time of error reading
      Rdistance= Rdistance/5.8/10;       // onverting time into distance(unit:cm)
      Rspeedd = Rdistance;              // reading-in Rspeedd(right speed) with distance 
    }  
    
void loop()
  {
    myservo.write(90);  //making motor regression, being ready for next measurement
    detection();        //measuring angle and deciding which direction it moves towards   
   if(directionn == 2)  //supposing direction = 2(back up)             
   {
     back(); 
     delay(800);                    //  back up
     left() ;      
     delay(200);              //moving slightly towards left(avoiding locked)
   }
   if(directionn == 6)           //supposing direction = 6(turning right)    
   {
     back();
     delay(100);  
     right();  
     delay(600);                 // turning right
   }
   if(directionn == 4)          //supposing direction = 4(turning left)    
   {  
     back(); 
     delay(600);      
     left(); 
     delay(600);                  // turning left
   }  
   if(directionn == 8)          //supposing direction =  = 8(going forwards)      
   { 
    advance();                 // going forwards normally  
    delay(100);  
   }
   }

Project 10:IR Remote Control of Smart Car


thumb

Introduction: This project ,regarding Arduino microcontroller as main control, uses IR module to receive IR remote signal and send the signal to Arduino. Arduino will analyses the signal and then control the driver motor and the motion of the car with IR remote control. In addition, you can observe the state of the car through keyestudio 1602 I2C Module.

Principle:

1.Connecting Arduino to IR receiving module ,Bluetooth module and IR receiving module communicating with IR remote control. 2.IR remote control will send these button message“thumb”“thumb”“thumb”“thumb”“thumb”“thumb”to IR receiving module. 3.IR receiving module will send signal to Arduino , and it will control the motion of the car . 4. When Arduino receiving this message“thumb”,the car goes forwards;when it receiving this“thumb”, the car goes backward;when it receiving“thumb”,the car turns left;when it receiving“thumb”,the car turns right;when it receiving“thumb”,the car stop;when it receiving“thumb”, the car quits.

Schematic Diagram:


thumb

Connection Diagram:


thumb

Sample Code:

#include <LiquidCrystal_I2C.h>   //including libraries of I2C-LCD1602 liquid crystal
#include <Wire.h>                //including libraries of I2C
#include <IRremote.h>
int RECV_PIN = 12;
IRrecv irrecv(RECV_PIN);
decode_results results;
#define IR_Go      0x00ff629d
#define IR_Back    0x00ffa857
#define IR_Left    0x00ff22dd
#define IR_Right   0x00ffc23d
#define IR_Stop    0x00ff02fd
#define IR_ESC     0x00ff52ad
LiquidCrystal_I2C lcd(0x27,16,2);  //defining liquid crystal
#define Lpwm_pin  5     //adjusting speed 
#define Rpwm_pin  10    //adjusting speed //
int pinLB=2;           // defining pin2 left rear
int pinLF=4;           // defining pin4 left front
int pinRB=7;           // defining pin7 right rear
int pinRF=8;           // defining pin8 right front
unsigned char Lpwm_val = 200;
unsigned char Rpwm_val = 200;
int Car_state=0;
void M_Control_IO_config(void)
{
  pinMode(pinLB,OUTPUT); // pin2
  pinMode(pinLF,OUTPUT); // pin4
  pinMode(pinRB,OUTPUT); // pin7 
  pinMode(pinRF,OUTPUT); // pin8
  pinMode(Lpwm_pin,OUTPUT); // pin11 (PWM) 
  pinMode(Rpwm_pin,OUTPUT); // pin10 (PWM)   
}
void Set_Speed(unsigned char Left,unsigned char Right)
{
  analogWrite(Lpwm_pin,Left);
  analogWrite(Rpwm_pin,Right);
}
void advance()     // going forward
    {
     digitalWrite(pinRB,LOW);  // making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,LOW);  // making motor move towards left rear
     digitalWrite(pinLF,HIGH); 
     Car_state = 1; 
     show_state();   
    }
void turnR()        //turning right(dual wheel)
    {
     digitalWrite(pinRB,LOW);  //making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,LOW);  //making motor move towards left front
     Car_state = 4;
     show_state();
    }
void turnL()        //turning left(dual wheel)
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,LOW );   //making motor move towards right front
     digitalWrite(pinLB,LOW);   //making motor move towards left rear
     digitalWrite(pinLF,HIGH);
     Car_state = 3;
     show_state();
    }    
void stopp()         //stop
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,HIGH);
     Car_state = 5;
     show_state();
    }
void back()          //back up
    {
     digitalWrite(pinRB,HIGH);  //making motor move towards right rear
     digitalWrite(pinRF,LOW);
     digitalWrite(pinLB,HIGH);  //making motor move towards left rear
     digitalWrite(pinLF,LOW);
     Car_state = 2;
     show_state() ;    
    }
void show_state(void)
{
  lcd.setCursor(0, 1);
   switch(Car_state)
   {
     case 1:lcd.print(" Go  ");Serial.print("\n GO");
     break;
     case 2:lcd.print("Back ");Serial.print("\n Back");
     break;
     case 3:lcd.print("Left ");Serial.print("\n Left");
     break;
     case 4:lcd.print("Right");Serial.print("\n Right");
     break;
     case 5:lcd.print("Stop ");Serial.print("\n Stop"); 
     break;
     default:
     break;
   }
}              
void LCD1602_init(void)            //function of initialization of liquid crystal 
{
  lcd.init();  //invoking initialized function in LiquidCrystal_I2C.h  
  delay(10);   //delaying for10 millisecond
  lcd.backlight(); //open backlight of LCD1602
  lcd.clear();     //clear screen
}
void IR_Control(void)
{
   unsigned long Key;
   lcd.setCursor(0,0);  //setting cursor in the first row and column
   lcd.print("IR_Ctr          ");
  while(Key!=IR_ESC)
  {
   if(irrecv.decode(&results)) //judging if serial port receives data    
  {
     Key = results.value;
    switch(Key)
     {
       case IR_Go:advance();   //UP
       break;
       case IR_Back: back();   //back
       break;
       case IR_Left:turnL();   //Left    
       break;
       case IR_Right:turnR(); //Righ
       break;
       case IR_Stop:stopp();   //stop
       break;
       default: 
       break;      
     } 
     irrecv.resume(); // Receive the next value
    } 
  }
  lcd.clear();
  lcd.setCursor(0, 0);  //setting cursor in the first row and column,
  lcd.print("  Wait  Signal  ");
  stopp();
}
void setup() 
{ 
   LCD1602_init();
   M_Control_IO_config();
   Set_Speed(Lpwm_val,Rpwm_val);
   irrecv.enableIRIn(); // Start the receiver
   Serial.begin(9600);   //initializing serial port, Bluetooth used as serial port, setting baud ratio at 9600 
   lcd.setCursor(0, 0);  //setting cursor at the first row and column
   lcd.print("  Wait  Signal  ");
   stopp();  
}
void loop() 
{  
   if (irrecv.decode(&results)) {
      if(results.value == IR_Stop )IR_Control();
      irrecv.resume(); // Receive the next value   
  } 
}

Project 11:Distance Detecting of Smart Car


thumb

Introduction:

This project ,regarding Arduino as main control, detect front obstacle by ultrasonic sensor and platform motor, and send the feedback to Arduino. Arduino will analyses the feedback signal and then control the driver motor to adjust the car diversion. Finally the car is able to avoid obstacle automatically and keep going.

In addition, you can observe the state and speed of the car , the angle of motor , and the distance between car and obstacle through keyestudio 1602 I2C Module.

Principle:

1.Ultrasonic detecting distance: one port emits high level more than 10 US. Once it outputting level, open potentiometer to time. When the port becomes low level, read out current value. Use the time of detecting distance to calculate distance.
2.Use ultrasonic to detect the distance between obstacle and car, so that control the motion of the car according to the data.
3.If the distance between the car and obstacle is less than 35 cm, the car goes backward; if the distance is no less than 10 cm, the car goes forwards; if the distance is less than 60 cm , the motor turns to detect the distance between car and left obstacle or right obstacle; if the distance between car and left obstacle, the distance between car and right obstacle are less than 35 cm, the car goes backward; if the distance between car and left obstacle is larger , the car turns left; if the distance between car and left obstacle is less than or equal to the distance between car and right obstacle, the car turns right.

Schematic Diagram:


thumb

Connection Diagram:


thumb

Sample Code:

#include <LiquidCrystal_I2C.h>   //including libraries of I2C-LCD1602 liquid crystal 
#include <Wire.h>              //including libraries of I2C
//////////////////////////////////////////////////
int inputPin=A0;  // ultrasonic module   ECHO to A0
int outputPin=A1;  // ultrasonic module  TRIG to A1
LiquidCrystal_I2C lcd(0x27,16,2);   //defining liquid crystal
#define Lpwm_pin  5     //pin of controlling speed---- ENA of motor driver board
#define Rpwm_pin  10    //pin of controlling speed---- ENB of motor driver board
int pinLB=2;             //pin of controlling turning---- IN1 of motor driver board
int pinLF=4;             //pin of controlling turning---- IN2 of motor driver board
int pinRB=7;            //pin of controlling turning---- IN3 of motor driver board
int pinRF=8;            //pin of controlling turning---- IN4 of motor driver board
unsigned char Lpwm_val = 250; //initialized left wheel speed at 250
unsigned char Rpwm_val = 250; //initialized right wheel speed at 250
int Car_state=0;             //the working state of car
int servopin=3;              //defining digital port pin 3, connecting to signal line of servo motor
int myangle;                //defining variable of angle
int pulsewidth;              //defining variable of pulse width
unsigned char DuoJiao=60;    //initialized angle of motor at 60°

void servopulse(int servopin,int myangle) //defining a function of pulse
{
pulsewidth=(myangle*11)+500; //converting angle into pulse width value at 500-2480 
digitalWrite(servopin,HIGH); //increasing the level of motor interface to upmost
delayMicroseconds(pulsewidth); //delaying microsecond of pulse width value
digitalWrite(servopin,LOW); //decreasing the level of motor interface to the least
delay(20-pulsewidth/1000);
}
void Set_servopulse(int set_val)
{
 for(int i=0;i<=10;i++)  //giving motor enough time to turn to assigning point
   servopulse(servopin,set_val); //invokimg pulse function
}
void M_Control_IO_config(void)
{
  pinMode(pinLB,OUTPUT); // /pin 2
  pinMode(pinLF,OUTPUT); // pin 4
  pinMode(pinRB,OUTPUT); // pin 7
  pinMode(pinRF,OUTPUT);  // pin 8
  pinMode(Lpwm_pin,OUTPUT);  // pin 11 (PWM) 
  pinMode(Rpwm_pin,OUTPUT);  // pin10(PWM)   
}
void Set_Speed(unsigned char Left,unsigned char Right) //function of setting speed
{
  analogWrite(Lpwm_pin,Left);
  analogWrite(Rpwm_pin,Right);
}
void advance()    //  going forward
    {
     digitalWrite(pinRB,LOW);  // making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,LOW);  // making motor move towards left rear
     digitalWrite(pinLF,HIGH); 
     Car_state = 1; 
     show_state();   
    }
void turnR()        //turning right(dual wheel)
    {
     digitalWrite(pinRB,LOW);  //making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,LOW);  //making motor move towards left front
     Car_state = 4;
     show_state();
    }
void turnL()         //turning left(dual wheel)
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,LOW );   //making motor move towards right front
     digitalWrite(pinLB,LOW);   //making motor move towards left rear
     digitalWrite(pinLF,HIGH);
     Car_state = 3;
     show_state();
    }    
void stopp()        //stop
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,HIGH);
     Car_state = 5;
     show_state();
    }
void back()         //back up
    {
     digitalWrite(pinRB,HIGH);  //making motor move towards right rear     
     digitalWrite(pinRF,LOW);
     digitalWrite(pinLB,HIGH);  //making motor move towards left rear
     digitalWrite(pinLF,LOW);
     Car_state = 2;
     show_state() ;    
    }
void show_state(void)
{
  lcd.setCursor(0, 1);
   switch(Car_state)
   {
     case 1:lcd.print(" Go  ");Serial.print(" \r\n GO");
     break;
     case 2:lcd.print("Back ");Serial.print(" \r\n Back");
     break;
     case 3:lcd.print("Left ");Serial.print(" \r\n Left");
     break;
     case 4:lcd.print("Right");Serial.print(" \r\n Right");
     break;
     case 5:lcd.print("Stop ");Serial.print(" \r\n Stop"); 
     break;
     default:
     break;
   }
}              
void LCD1602_init(void)            //including initialized function of liquid crystal
{
  lcd.init();  //invoking initialized function of LCD in LiquidCrystal_I2C.h  
  delay(10);  //delaying for 10 millisecond
  lcd.backlight(); //open backlight of LCD1602
  lcd.clear();    //clear screen
}  
void Show_V(unsigned char V)
{
     lcd.setCursor(11, 0);
     lcd.print("V=    ");
     lcd.setCursor(13, 0);
     lcd.print(V,DEC);
     Serial.print("\n Speed = ");
     Serial.print(V,DEC); 
}
void Show_DuoJiao(unsigned char Jiao)
{
     lcd.setCursor(6,1);
     lcd.print("C=    ");
     lcd.setCursor(8, 1);
     lcd.print(Jiao,DEC);
     Serial.print("\n JiaoDu = ");
     Serial.print(Jiao,DEC); 
}
void Self_Control(void)//self-going, ultrasonic obstacle avoidance
{
   int H;
   lcd.setCursor(0, 0);  //setting cursor in the first row and column
   lcd.print("Self_Ctr        ");
   Show_V(Lpwm_val);
   Set_servopulse(DuoJiao);
   Show_DuoJiao(DuoJiao); 
   H = Ultrasonic_Ranging(1);
   delay(300);   
   if(Ultrasonic_Ranging(1) < 35)         
   {
       stopp();              
       delay(100);
       back();               
       delay(50);
    }
           
  if(Ultrasonic_Ranging(1) < 60)        
      {
        stopp();  
        delay(100);            
        Set_servopulse(5);
        Show_DuoJiao(5);
        int L = ask_pin_L(2);
        delay(300);      
         Set_servopulse(177);
         Show_DuoJiao(177);
        int R = ask_pin_R(3);
        delay(300);      

        if(ask_pin_L(2) > ask_pin_R(3))   
        {
         back(); 
        delay(100);      
        turnL();
       delay(400);                  
       stopp();  
       delay(50);            
       Set_servopulse(DuoJiao);
       Show_DuoJiao(DuoJiao); 
       H = Ultrasonic_Ranging(1);
       delay(500); 
        }
        
      if(ask_pin_L(2)  <= ask_pin_R(3))   
      {
       back();  
       delay(100);  
       turnR(); 
       delay(400);   
       stopp();  
       delay(50);            
       Set_servopulse(DuoJiao);
       Show_DuoJiao(DuoJiao); 
       H = Ultrasonic_Ranging(1);
       delay(300);        
        }   
        if (ask_pin_L(2)  < 35 && ask_pin_R(3)< 35)   
        {
       stopp();            
       delay(50);
       back(); 
       delay(50);                   
        }          
      }
      else                      
      {
      advance();                
      }                 
}
int Ultrasonic_Ranging(unsigned char Mode)//function of ultrasonic distance detecting ,MODE=1,displaying,no displaying under other situation

{ 
  int old_distance;
  digitalWrite(outputPin, LOW);  
  delayMicroseconds(2); 
  digitalWrite(outputPin, HIGH); 
  delayMicroseconds(10); 
  digitalWrite(outputPin, LOW);    
  int distance = pulseIn(inputPin, HIGH);  // reading the duration of high level
  distance= distance/58;   // Transform pulse time to distance   
  if(Mode==1){
         lcd.setCursor(11, 1);
         lcd.print("H=    ");
         lcd.setCursor(13, 1);
         lcd.print(distance,DEC);
         Serial.print("\n H = ");
         Serial.print(distance,DEC); 
         return distance;
  }
   else  return distance;
} 
int ask_pin_L(unsigned char Mode)    
  { 
  int old_Ldistance;
  digitalWrite(outputPin, LOW);  
  delayMicroseconds(2); 
  digitalWrite(outputPin, HIGH); 
  delayMicroseconds(10); 
  digitalWrite(outputPin, LOW);    
  int Ldistance = pulseIn(inputPin, HIGH); 
  Ldistance= Ldistance/58;   // Transform pulse time to distance   
  if(Mode==2){
         lcd.setCursor(11, 1);
         lcd.print("L=    ");
         lcd.setCursor(13, 1);
         lcd.print(Ldistance,DEC);
         Serial.print("\n L = ");
         Serial.print(Ldistance,DEC); 
         return Ldistance;
  }
   else  return Ldistance;
} 
int ask_pin_R(unsigned char Mode)   
   { 
  int old_Rdistance;
  digitalWrite(outputPin, LOW);  
  delayMicroseconds(2); 
  digitalWrite(outputPin, HIGH); // 
  delayMicroseconds(10); 
  digitalWrite(outputPin, LOW);    
  int Rdistance = pulseIn(inputPin, HIGH); 
  Rdistance= Rdistance/58;   // Transform pulse time to distance   
  if(Mode==3){
         lcd.setCursor(11, 1);
         lcd.print("R=    ");
         lcd.setCursor(13, 1);
         lcd.print(Rdistance,DEC);
         Serial.print("\n R = ");
         Serial.print(Rdistance,DEC); 
         return Rdistance;
  }
   else  return Rdistance;
} 

void setup() 
{ 
   pinMode(servopin,OUTPUT);  //setting motor interface as output
   LCD1602_init();            //initializing 1602
   M_Control_IO_config();     //motor controlling the initialization of IO
   Set_Speed(Lpwm_val,Rpwm_val);  //setting initialized speed
   Set_servopulse(DuoJiao);       //setting initialized motor angle
   pinMode(inputPin, INPUT);      //starting receiving IR remote control signal
   pinMode(outputPin, OUTPUT);    //IO of ultrasonic module
   Serial.begin(9600);            //initialized serial port , using Bluetooth as serial port, setting baud 
   lcd.setCursor(0, 0);           //setting cursor at 0.0
   lcd.print("  Wait  Signal  ");  //LCD printing character string
   stopp();                       //stop
} 
void loop() 
{  
 
        Self_Control();   
}

Project 12:Bluetooth Remote Control of Smart Car


thumb

Introduction:

This project , regarding Arduino as main control, use Bluetooth module to receive signal from mobile phone, and send the signal to Arduino. Arduino will analyses the signal and then control the driver motor to control the motion of the car. In addition, you can observe the state and speed of the car , the angle of motor , and the distance between car and obstacle through keyestudio 1602 I2C Module.

Principle:

1.Connecting Aduino to Bluetooth module , this module communicating with APP on the mobile phone
2.APP sending “U”“D”“L”“R”“S” to Bluetooth module
3.Bluetooth module will send the received massage to Arduino, and Arduino controls the car correspondingly.
4. When Arduino receiving “U”, the car goes forward; when Arduino receiving “D”, it goes backward; when Arduino receiving “R”, it turns right; when receiving “S”, it stops moving.

Schematic Diagram:


thumb

Connection Diagram:


thumb

Sample Code:

#include <LiquidCrystal_I2C.h>   //including the libraries of I2C-LCD1602 liquid crystal 
#include <Wire.h>                //including the libraries of I2C
unsigned char Bluetooth_val;       //defining variable val
LiquidCrystal_I2C lcd(0x27,16,2);  //defining liquid crystal
#define Lpwm_pin  5     //adjusting speed  
#define Rpwm_pin  10    //adjusting speed  //
int pinLB=2;     // defining pin2 left rear
int pinLF=4;     // defining pin4 left front
int pinRB=7;    // defining pin7 right rear
int pinRF=8;    // defining pin8 right front
unsigned char Lpwm_val = 255;
unsigned char Rpwm_val = 255;
int Car_state=0;
void M_Control_IO_config(void)
{
  pinMode(pinLB,OUTPUT); // pin 2
  pinMode(pinLF,OUTPUT); // pin 4
  pinMode(pinRB,OUTPUT); // pin 7 
  pinMode(pinRF,OUTPUT); // pin 8
  pinMode(Lpwm_pin,OUTPUT); // pin 11 (PWM) 
  pinMode(Rpwm_pin,OUTPUT); // pin 10 (PWM)   
}
void Set_Speed(unsigned char Left,unsigned char Right)
{
  analogWrite(Lpwm_pin,Left);
  analogWrite(Rpwm_pin,Right);
}
void advance()     //  going forward
    {
     digitalWrite(pinRB,LOW);  // making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,LOW);  // making motor move towards left rear
     digitalWrite(pinLF,HIGH); 
     Car_state = 1; 
     show_state();   
    }
void turnR()        //turning right(dual wheel)
    {
     digitalWrite(pinRB,LOW);  //making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,LOW);  //making motor move towards left front
     Car_state = 4;
     show_state();
    }
void turnL()        //turning left(dual wheel)
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,LOW );   //making motor move towards right front
     digitalWrite(pinLB,LOW);   //making motor move towards left rear
     digitalWrite(pinLF,HIGH);
     Car_state = 3;
     show_state();
    }    
void stopp()         //stop
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,HIGH);
     Car_state = 5;
     show_state();
    }
void back()          //back up
    {
     digitalWrite(pinRB,HIGH);  //making motor move towards right rear
     digitalWrite(pinRF,LOW);
     digitalWrite(pinLB,HIGH);  //making motor move towards left rear
     digitalWrite(pinLF,LOW);
     Car_state = 2;
     show_state() ;    
    }
void show_state(void)
{
  lcd.setCursor(0, 1);
   switch(Car_state)
   {
     case 1:lcd.print(" Go  ");
     break;
     case 2:lcd.print("Back ");
     break;
     case 3:lcd.print("Left ");
     break;
     case 4:lcd.print("Right");
     break;
     case 5:lcd.print("stop ");
     break;
     default:
     break;
   }
}              
void LCD1602_init(void)            //including initialized function of liquid crystal
{
  lcd.init();  //invoking initialized function of LCD in LiquidCrystal_I2C.h  
  delay(10);   //delaying for 10 millisecond
  lcd.backlight(); //open backlight of LCD1602
  lcd.clear();     //clear screen
}    
void setup() 
{ 
   LCD1602_init();
   M_Control_IO_config();
   Set_Speed(Lpwm_val,Rpwm_val);
   Serial.begin(9600);   //initialized serial port , using Bluetooth as serial port, setting baud at 9600 
   lcd.setCursor(0, 0);  //setting cursor in the first row and column
   lcd.print("   Wait  Sigal");
   stopp(); 
}
void loop() 
{  
   lcd.setCursor(0, 0);  //setting cursor in the first row and column
   lcd.print("BluetoothControl");
 
   if(Serial.available()) //to judge whether the serial port receives the data.
    {
     Bluetooth_val=Serial.read();  //reading (Bluetooth) data of serial port,giving the value of val;
    switch(Bluetooth_val)
     {
       case 'U':advance(); //UP
       break;
       case 'D': back();   //back
       break;
       case 'L':turnL();   //Left
       break;
       case 'R':turnR();  //Right
       break;
       case 'S':stopp();    //stop
       break;   
     }
    } 
}

Project 13:: 5 in 1 (Line Tracking, Obstacle Avoidance, Bluetooth and IR Remote Control, Distance Detecting ) Muilti-functional Car


thumb

Introduction:

In this project, we will put five functions, namely line tracking, obstacle avoidance, Bluetooth and IR remote control, distance detecting, together into one to realize the working mode of the car. Press“5”button of IR remote control to start line tracking, “6” to start ultrasonic obstacle avoidance and distance detecting, “7” to start IR remote control, “8”to start Bluetooth remote control, and press reset button to enter initialized mode.

Schematic Diagram:


thumb

Connection Diagram:


thumb

Sample Code:

#include <LiquidCrystal_I2C.h>   //including libraries of I2C-LCD1602 liquid crystal 
#include <Wire.h>              //including libraries of I2C
#include <IRremote.h>          //including libraries of remote control
#define RECV_PIN  12        //pin 12 of IR remoter control receiver
IRrecv irrecv(RECV_PIN);      //defining pin 12 of IR remoter control
decode_results results;         //cache of decode of IR remoter control
#define IR_Go       0x00ff629d //going forward
#define IR_Back     0x00ffa857  //going backward
#define IR_Left     0x00ff22dd  //turning left
#define IR_Right    0x00ffc23d  //turning right
#define IR_Stop     0x00ff02fd  //stop 
#define IR_Servo_L  0x00ff6897  //motor turning left
#define IR_Servo_R  0x00ff9867  //motor turning right
#define IR_Speed_UP     0x00ffb04f //increasing speed
#define IR_Speed_DOWN   0x00ff30cf //decreasing speed
#define IR_XunJi_Mode   0x00ff18e7
#define IR_Self_Control  0x00ff7a85  //ultrasonic distance detecting 
#define IR_IR_Control  0x00ff10ef
#define IR_Bluetooth_Control  0x00ff38c7
#define IR_ESC      0x00ff52ad  //quitting from remote control
//////////////////////////////////////////////////
#define SensorLeft    6   //sensor left pin of line tracking module 
#define SensorMiddle  9   //sensor middle pin of line tracking module
#define SensorRight   11  //sensor right pin of line tracking module
unsigned char SL;        //state of left sensor of line tracking module
unsigned char SM;        //state of middle sensor of line tracking module
unsigned char SR;        //state of right sensor of line tracking module
int inputPin=A0;  // ultrasonic module   ECHO to A0
int outputPin=A1;  // ultrasonic module  TRIG to A1
unsigned char Bluetooth_val;       // ultrasonic module  TRIG to A1
LiquidCrystal_I2C lcd(0x27,16,2);   //defining liquid crystal
#define Lpwm_pin  5     //pin of controlling speed---- ENA of motor driver board
#define Rpwm_pin  10    //pin of controlling speed---- ENB of motor driver board
int pinLB=2;             //pin of controlling turning---- IN1 of motor driver board
int pinLF=4;             //pin of controlling turning---- IN2 of motor driver board
int pinRB=7;            //pin of controlling turning---- IN3 of motor driver board
int pinRF=8;            //pin of controlling turning---- IN4 of motor driver board
unsigned char Lpwm_val = 250; //initialized left wheel speed at 250
unsigned char Rpwm_val = 250; //initialized right wheel speed at 250
int Car_state=0;             //the working state of car
int servopin=3;              //defining digital port pin 3, connecting to signal line of servo motor
int myangle;                //defining variable of angle
int pulsewidth;              //defining variable of pulse width
unsigned char DuoJiao=60;    //initialized angle of motor at 60°
void Sensor_IO_Config()     //IO initialized function of three line tracking , all setting at input
{
  pinMode(SensorLeft,INPUT);
  pinMode(SensorMiddle,INPUT);
  pinMode(SensorRight,INPUT);
}
void Sensor_Scan(void) //function of reading-in signal of line tracking module 
{
  SL = digitalRead(SensorLeft);
  SM = digitalRead(SensorMiddle);
  SR = digitalRead(SensorRight);
}
void servopulse(int servopin,int myangle) //defining a function of pulse
{
pulsewidth=(myangle*11)+500; //converting angle into pulse width value at 500-2480 
digitalWrite(servopin,HIGH); //increasing the level of motor interface to upmost
delayMicroseconds(pulsewidth); //delaying microsecond of pulse width value
digitalWrite(servopin,LOW); //decreasing the level of motor interface to the least
delay(20-pulsewidth/1000);
}
void Set_servopulse(int set_val)
{
 for(int i=0;i<=10;i++)  //giving motor enough time to turn to assigning point
   servopulse(servopin,set_val); //invokimg pulse function
}
void M_Control_IO_config(void)
{
  pinMode(pinLB,OUTPUT); // /pin 2
  pinMode(pinLF,OUTPUT); // pin 4
  pinMode(pinRB,OUTPUT); // pin 7
  pinMode(pinRF,OUTPUT);  // pin 8
  pinMode(Lpwm_pin,OUTPUT);  // pin 11 (PWM) 
  pinMode(Rpwm_pin,OUTPUT);  // pin10(PWM)   
}
void Set_Speed(unsigned char Left,unsigned char Right) //function of setting speed
{
  analogWrite(Lpwm_pin,Left);
  analogWrite(Rpwm_pin,Right);
}
void advance()    //  going forward
    {
     digitalWrite(pinRB,LOW);  // making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,LOW);  // making motor move towards left rear
     digitalWrite(pinLF,HIGH); 
     Car_state = 1; 
     show_state();   
    }
void turnR()        //turning right(dual wheel)
    {
     digitalWrite(pinRB,LOW);  //making motor move towards right rear
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,LOW);  //making motor move towards left front
     Car_state = 4;
     show_state();
    }
void turnL()         //turning left(dual wheel)
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,LOW );   //making motor move towards right front
     digitalWrite(pinLB,LOW);   //making motor move towards left rear
     digitalWrite(pinLF,HIGH);
     Car_state = 3;
     show_state();
    }    
void stopp()        //stop
    {
     digitalWrite(pinRB,HIGH);
     digitalWrite(pinRF,HIGH);
     digitalWrite(pinLB,HIGH);
     digitalWrite(pinLF,HIGH);
     Car_state = 5;
     show_state();
    }
void back()         //back up
    {
     digitalWrite(pinRB,HIGH);  //making motor move towards right rear     
     digitalWrite(pinRF,LOW);
     digitalWrite(pinLB,HIGH);  //making motor move towards left rear
     digitalWrite(pinLF,LOW);
     Car_state = 2;
     show_state() ;    
    }
void show_state(void)
{
  lcd.setCursor(0, 1);
   switch(Car_state)
   {
     case 1:lcd.print(" Go  ");Serial.print(" \r\n GO");
     break;
     case 2:lcd.print("Back ");Serial.print(" \r\n Back");
     break;
     case 3:lcd.print("Left ");Serial.print(" \r\n Left");
     break;
     case 4:lcd.print("Right");Serial.print(" \r\n Right");
     break;
     case 5:lcd.print("Stop ");Serial.print(" \r\n Stop"); 
     break;
     default:
     break;
   }
}              
void LCD1602_init(void)            //including initialized function of liquid crystal
{
  lcd.init();  //invoking initialized function of LCD in LiquidCrystal_I2C.h  
  delay(10);  //delaying for 10 millisecond
  lcd.backlight(); //open backlight of LCD1602
  lcd.clear();    //clear screen
}  
void Show_V(unsigned char V)
{
     lcd.setCursor(11, 0);
     lcd.print("V=    ");
     lcd.setCursor(13, 0);
     lcd.print(V,DEC);
     Serial.print("\n Speed = ");
     Serial.print(V,DEC); 
}
void Show_DuoJiao(unsigned char Jiao)
{
     lcd.setCursor(6,1);
     lcd.print("C=    ");
     lcd.setCursor(8, 1);
     lcd.print(Jiao,DEC);
     Serial.print("\n JiaoDu = ");
     Serial.print(Jiao,DEC); 
}
void Xunji_Mode(void) //function of line tracking 
{
 lcd.setCursor(0, 0);  //setting cursor in the first row and column
 lcd.print("Xunji_Mode           ");
 Sensor_Scan();
 if (SM == HIGH)// middle sensor in black area
{
if (SL == LOW & SR == HIGH) // black on left, white on right, turn left
{
turnR();
}
else if (SR == LOW & SL == HIGH) // white on left, black on right, turn right
{
turnL();
}
else // white on both sides, going forward
{
advance();
}
}
else // middle sensor on white area
{
if (SL== LOW & SR == HIGH)// black on left, white on right, turn left
{
turnR();
}
else if (SR == LOW & SL == HIGH) // white on left, black on right, turn right
{
turnL();
}
else // all white, stop
{
back();
delay(100);
stopp() ; 
}
}
}
void Self_Control(void)//self-going, ultrasonic obstacle avoidance
{
   int H;
   lcd.setCursor(0, 0);  //setting cursor in the first row and column
   lcd.print("Self_Ctr        ");
   Show_V(Lpwm_val);
   Set_servopulse(DuoJiao);
   Show_DuoJiao(DuoJiao); 
   H = Ultrasonic_Ranging(1);
   delay(300);   
   if(Ultrasonic_Ranging(1) < 35)         
   {
       stopp();              
       delay(100);
       back();               
       delay(50);
    }
           
  if(Ultrasonic_Ranging(1) < 60)        
      {
        stopp();  
        delay(100);            
        Set_servopulse(5);
        Show_DuoJiao(5);
        int L = ask_pin_L(2);
        delay(300);      
         Set_servopulse(177);
         Show_DuoJiao(177);
        int R = ask_pin_R(3);
        delay(300);      

        if(ask_pin_L(2) > ask_pin_R(3))   
        {
         back(); 
        delay(100);      
        turnL();
       delay(400);                  
       stopp();  
       delay(50);            
       Set_servopulse(DuoJiao);
       Show_DuoJiao(DuoJiao); 
       H = Ultrasonic_Ranging(1);
       delay(500); 
        }
        
      if(ask_pin_L(2)  <= ask_pin_R(3))   
      {
       back();  
       delay(100);  
       turnR(); 
       delay(400);   
       stopp();  
       delay(50);            
       Set_servopulse(DuoJiao);
       Show_DuoJiao(DuoJiao); 
       H = Ultrasonic_Ranging(1);
       delay(300);        
        }   
        if (ask_pin_L(2)  < 35 && ask_pin_R(3)< 35)   
        {
       stopp();            
       delay(50);
       back(); 
       delay(50);                   
        }          
      }
      else                      
      {
      advance();                
      }                 
}
int Ultrasonic_Ranging(unsigned char Mode)//function of ultrasonic distance detecting ,MODE=1,displaying,no displaying under other situation

{ 
  int old_distance;
  digitalWrite(outputPin, LOW);  
  delayMicroseconds(2); 
  digitalWrite(outputPin, HIGH); 
  delayMicroseconds(10); 
  digitalWrite(outputPin, LOW);    
  int distance = pulseIn(inputPin, HIGH);  // reading the duration of high level
  distance= distance/58;   // Transform pulse time to distance   
  if(Mode==1){
         lcd.setCursor(11, 1);
         lcd.print("H=    ");
         lcd.setCursor(13, 1);
         lcd.print(distance,DEC);
         Serial.print("\n H = ");
         Serial.print(distance,DEC); 
         return distance;
  }
   else  return distance;
} 
int ask_pin_L(unsigned char Mode)    
  { 
  int old_Ldistance;
  digitalWrite(outputPin, LOW);  
  delayMicroseconds(2); 
  digitalWrite(outputPin, HIGH); 
  delayMicroseconds(10); 
  digitalWrite(outputPin, LOW);    
  int Ldistance = pulseIn(inputPin, HIGH); 
  Ldistance= Ldistance/58;   // Transform pulse time to distance   
  if(Mode==2){
         lcd.setCursor(11, 1);
         lcd.print("L=    ");
         lcd.setCursor(13, 1);
         lcd.print(Ldistance,DEC);
         Serial.print("\n L = ");
         Serial.print(Ldistance,DEC); 
         return Ldistance;
  }
   else  return Ldistance;
} 
int ask_pin_R(unsigned char Mode)   
   { 
  int old_Rdistance;
  digitalWrite(outputPin, LOW);  
  delayMicroseconds(2); 
  digitalWrite(outputPin, HIGH); // 
  delayMicroseconds(10); 
  digitalWrite(outputPin, LOW);    
  int Rdistance = pulseIn(inputPin, HIGH); 
  Rdistance= Rdistance/58;   // Transform pulse time to distance   
  if(Mode==3){
         lcd.setCursor(11, 1);
         lcd.print("R=    ");
         lcd.setCursor(13, 1);
         lcd.print(Rdistance,DEC);
         Serial.print("\n R = ");
         Serial.print(Rdistance,DEC); 
         return Rdistance;
  }
   else  return Rdistance;
} 

void IR_Control(void)   //remote control,when pressing“#”,it quitting from the mode
{
   unsigned long Key;
   lcd.setCursor(0,0);  //setting cursor in the first row and column
   lcd.print("IR_Ctr          ");
  while(Key!=IR_ESC)
  {
   if(irrecv.decode(&results))  //to judge whether serial port receive data
    {
     Key = results.value;
    switch(Key)
     {
       case IR_Go:advance();   //UP
       break;
       case IR_Back: back();   //back
       break;
       case IR_Left:turnL();   //Left    
       break;
       case IR_Right:turnR(); //Righ
       break;
       case IR_Stop:stopp();   //stop
       break;
       case IR_Servo_L: if(DuoJiao<=180){  //motor turning left
                  DuoJiao+=10;
                  Set_servopulse(DuoJiao);
                  Show_DuoJiao(DuoJiao);}             
       break;
      case IR_Servo_R: if(DuoJiao-10>=0){  //motor turning right 
                  DuoJiao-=10;
                  Set_servopulse(DuoJiao);
                  Show_DuoJiao(DuoJiao);} 
       break;
      case IR_Speed_UP:if(Rpwm_val+10<=250&&Rpwm_val+10<=250){  //increasing speed
                  Lpwm_val+=10; Rpwm_val+=10;
                  Set_Speed(Lpwm_val,Rpwm_val);
                  Show_V(Lpwm_val);
                  }
       break;
      case IR_Speed_DOWN:if(Rpwm_val-10>=0&&Rpwm_val-10>=0){  //decreasing speed
                  Lpwm_val-=10; Rpwm_val-=10;
                  Set_Speed(Lpwm_val,Rpwm_val);
                  Show_V(Lpwm_val);
                  }
       break;
       default: 
       break;      
     } 
     irrecv.resume(); // Receive the next value
    } 
  }
  lcd.clear();
  lcd.setCursor(0, 0);  //setting cursor in the first row and column
  lcd.print("  Wait  Signal  ");
  stopp();
}
void Bluetooth_Control() //Bluetooth remote control
{
   lcd.setCursor(0, 0);  //setting cursor in the first row and column
   lcd.print("BluetoothControl");
 
   if(Serial.available()) //to judge whether serial port receive data
    {
     Bluetooth_val=Serial.read();  //reading value of Bluetooth serial port, giving the value to val
    switch(Bluetooth_val)
     {
       case 'U':advance(); //UP
       break;
       case 'D': back();   //back
       break;
       case 'L':turnL();   //Left
       break;
       case 'R':turnR();  //Right
       break;
       case 'S':stopp();    //stop
       break;   
     }
    } 
}

void setup() 
{ 
   pinMode(servopin,OUTPUT);  //setting motor interface as output
   LCD1602_init();            //initializing 1602
   M_Control_IO_config();     //motor controlling the initialization of IO
   Set_Speed(Lpwm_val,Rpwm_val);  //setting initialized speed
   Set_servopulse(DuoJiao);       //setting initialized motor angle
   Sensor_IO_Config();            //initializing IO of line tracking module 
   irrecv.enableIRIn();           //starting receiving IR remote control signal
   pinMode(inputPin, INPUT);      //starting receiving IR remote control signal
   pinMode(outputPin, OUTPUT);    //IO of ultrasonic module
   Serial.begin(9600);            //initialized serial port , using Bluetooth as serial port, setting baud 
   lcd.setCursor(0, 0);           //setting cursor at 0.0
   lcd.print("  Wait  Signal  ");  //LCD printing character string
   stopp();                       //stop
} 
void loop() 
{  
 
   if (irrecv.decode(&results)) 
   {//when receiving a button
      if(results.value == IR_XunJi_Mode) 
      { 
       while(IR_XunJi_Mode)
       { 
        Xunji_Mode();
       }   //pressing “OK” on remote controller, and entering remote control mode
      } 
      if(results.value == IR_Self_Control) 
       {
        while(IR_Self_Control)
        {
        Self_Control();  //pressing “OK” on remote controller, and entering remote control mode        
       } 
       }
      if(results.value == IR_IR_Control) 
       { 
        while(IR_IR_Control)
        {
        IR_Control();  //pressing “OK” on remote controller, and entering remote control mode        
       } 
       }
      if(results.value == IR_Bluetooth_Control) 
       {
        while(IR_Bluetooth_Control)
        {
        Bluetooth_Control();  //pressing “OK” on remote controller, and entering remote control mode
        }  
       } 
      irrecv.resume(); // Receive the next value  
    } 
  delay(10);
}

Result

The car is controlled by IR remote control and mobile phone Bluetooth together. After connection, press number 5 key of IR remote control, and the car enter into line tracking mode to go along with black line. When press reset, and then press number 6 key, the car enter into ultrasonic obstacle avoidance mode and it goes with automatic obstacle avoidance, displaying current condition and distance between car and obstacle on LCD. Press reset and then number 7 key , the car is in IR control, its motion is controlled by IR up, down, right and left key, “OK” means stop. Number 1 and 2 key control rotation of motor, and 3 and 4 key control move speed. Reset again, the car go into Bluetooth mode, connecting to Bluetooth APP, and then control the motion of the car by APP.

Resources

Video

http://www.keyestudio.com/wp/2016/09/ks0192-keyestudio-4wd-bluetooth-multi-functional-car-assembly-video/

Datasheet

PDF:http://www.keyestudio.com/files/index/download/id/1479115839/

APP:http://www.keyestudio.com/files/index/download/id/1479115841/

Codes:http://www.keyestudio.com/files/index/download/id/1479115842/

Buy from

http://www.keyestudio.com/keyestudio-4wd-bluetooth-multi-functional-car.html

https://www.amazon.com/keyestudio-Bluetooth-Multi-functional-Starter-Arduino/dp/B01N9HV6ZH/ref=sr_1_1?s=toys-and-games&ie=UTF8&qid=1486963013&sr=1-1&keywords=Ks0192+keyestudio+4WD+Bluetooth+Multi-functional+Car