Ks0234 keyestudio Yellow LED Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
(Created page with "==Introduction== This is a yellow LED module. The main function is to control a plugin LED on and off. When connecting to ARDUINO, after programming, it will emit yellow ligh...")
 
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
==Introduction==
 
 
<br>
== Introduction ==
This is a yellow LED module. The main function is to control a plugin LED on and off.  
This is a yellow LED module. The main function is to control a plugin LED on and off.  
When connecting to ARDUINO, after programming, it will emit yellow light color.
When connecting to ARDUINO, after programming, it will emit yellow light color.<br>
The pin pitch of 3Pin is 2.54mm.
The pin pitch of 3Pin is 2.54mm.
This LED module has 3 Pins; - pin is connected to ground, + pin is connected to VCC(3.3-5V), S pin is for signal control; you can set the High or Low level to control the LED on and off.  
This LED module has 3 Pins; - pin is connected to ground, + pin is connected to VCC(3.3-5V), S pin is for signal control; you can set the High or Low level to control the LED on and off. <br>
You can combine with other sensors to do various interactive experiments.  
You can combine with other sensors to do various interactive experiments. <br>
You can also choose other LED modules to emit different light color like blue, white, green and red.
You can also choose other LED modules to emit different light color like blue, white, green and red.<br>
<br>[[File:Ks0234-1.png|400px|frameless|thumb]]<br>
 
<br>
== Features ==
* Control interface: Digital
* Working voltage: DC 3.3-5V
* Pin pitch: 2.54mm
* LED color: yellow
* Easy to use
* Useful for light projects
 
 
<br>
== Connect It Up ==
Connect the LED module to control board using three jumper wires. Then connect the control board to your PC with a USB cable.<br>
<br>[[File:Ks0234-2.png|600px|frameless|thumb]]<br>
 
<br>
== Upload the Code ==
Copy and paste below code to Arduino IDE and upload.  <br>
<pre>
int led = 7;
void setup()
{
  pinMode(led, OUTPUT);    //Set Pin7 as output
}
void loop()
{    digitalWrite(led, HIGH);  //Turn off led
          delay(1000);
          digitalWrite(led, LOW);    //Turn on led
          delay(1000);
}
</pre>
 
 
<br>
== What You Should See ==
The LED will flash on for one second, then off for one second, repeatedly and alternately. <br>
If it doesn’t, make sure you have assembled the circuit correctly and verified and uploaded the code to your board. <br>
 
 
<br>
==Resources ==
'''Download the PDF and Code:'''<br>
https://fs.keyestudio.com/KS0234
 
<br>
 
==Buy from ==
 
*[https://www.keyestudio.com/keyestudio-super-bright-emitting-color-piranha-led-module-yellow-p0404-p0404.html  '''Official Website''' ]
 
*[https://www.aliexpress.com/store/product/Keyestudio-Super-bright-emitting-color-Piranha-LED-module-YELLOW/1452162_32814245076.html?spm=2114.12010612.8148356.35.3c6c2933a14ywm    '''aliexpress store''']


==Features==
 Control interface: Digital
 Working voltage: DC 3.3-5V
 Pin pitch: 2.54mm
 LED color: yellow
 Easy to use
 Useful for light projects


==Connect It Up==
[[category: Module]]
Connect the LED module to control board using three jumper wires. Then connect the control board to your PC with a USB cable.

Latest revision as of 09:53, 8 January 2021



Introduction

This is a yellow LED module. The main function is to control a plugin LED on and off. When connecting to ARDUINO, after programming, it will emit yellow light color.
The pin pitch of 3Pin is 2.54mm. This LED module has 3 Pins; - pin is connected to ground, + pin is connected to VCC(3.3-5V), S pin is for signal control; you can set the High or Low level to control the LED on and off.
You can combine with other sensors to do various interactive experiments.
You can also choose other LED modules to emit different light color like blue, white, green and red.

thumb


Features

  • Control interface: Digital
  • Working voltage: DC 3.3-5V
  • Pin pitch: 2.54mm
  • LED color: yellow
  • Easy to use
  • Useful for light projects



Connect It Up

Connect the LED module to control board using three jumper wires. Then connect the control board to your PC with a USB cable.

thumb


Upload the Code

Copy and paste below code to Arduino IDE and upload.

int led = 7; 
void setup()
{
  pinMode(led, OUTPUT);     //Set Pin7 as output
}
void loop()
{    digitalWrite(led, HIGH);   //Turn off led
          delay(1000);
          digitalWrite(led, LOW);    //Turn on led
          delay(1000);
}



What You Should See

The LED will flash on for one second, then off for one second, repeatedly and alternately.
If it doesn’t, make sure you have assembled the circuit correctly and verified and uploaded the code to your board.



Resources

Download the PDF and Code:
https://fs.keyestudio.com/KS0234


Buy from