Ks0007 keyestudio L298P Motor Shield: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
Line 92: Line 92:
==Test Result==
==Test Result==
Upload well the code, you should see the two motors firstly turn forward for 8 seconds, then reverse for 8 seconds, repeatedly.  
Upload well the code, you should see the two motors firstly turn forward for 8 seconds, then reverse for 8 seconds, repeatedly.  
<br>[[Image:KS0007 Detail.png|800px|frameless]]<br>
<br>[[Image:KS0007 result.png|800px|frameless]]<br>
<br>
<br>



Revision as of 09:06, 14 September 2018

Keyestudio L298P Motor Shield

Introduction

You can use UNO R3 microcontroller and add external components to complete a variety of amazing experiments, such as smart robot DIY. When DIY your robot, it is necessary to use the motor driver board to drive the DC motors, however, sometimes need to connect the motor drive board to UNO using lots of jumper wires, pretty inconvenient.
Now, we have launched this keyestudio motor shield with L298P as core. Just simply stack it onto UNO R3 board when using. Note that the motor’s speed and direction interfaces have been connected. D3 is for controlling the speed of motor A, and D12 is for controlling the direction of motor A. D11 is for controlling the speed of motor B, and D13 is for controlling the direction.
The green terminal blocks should been connected to VIN /GND pins on the UNO. You can supply the power to the board via the terminal blocks or black DC jack of UNO. The maximum voltage supply is DC 18V.
Onboard also comes with through-hole pad, so you are able to weld the electronic elements to design a variety of prototyping circuits.

KS0007 back.jpg


Specifications

Logic part input voltage VD: 5V
Driving part input voltage VS VIN input 6.5 ~ 12V, PWRIN input 4.8 ~ 24V
Logic part working current Iss ≤36mA
Driving part working current Io ≤ 2A
Maximum dissipation power 25W (T=75℃)
Control signal input level High level: 2.3V ≤ Vin ≤ 5V Low level: -0.3V ≤ Vin ≤ 1.5V
Working temperature -25℃ to+130℃
Driver form Dual power H bridge driving


Controller Compatible


Technical Details

  • Dimensions: 60mm x 54mm
  • Weight: 20.8g


KS0007 Detail.jpg


PINOUT Instruction


KS0007 PINOUT.jpg


How to Test it ?

Connect it Up

Simply stack the shield onto UNO R3 board, then connect two motors to terminal block.

Upload the Code

Below is an example code, you can copy and paste it on Arduino IDE.

int E1 = 3;  
int M1 = 12;
int E2 =11;                        
int M2 = 13;                          

void setup()
{
    pinMode(M1, OUTPUT);  
    pinMode(M2, OUTPUT);
}

void loop()
{
    digitalWrite(M1,HIGH);  
    digitalWrite(M2, HIGH);      
    analogWrite(E1, 200);   // PWM regulate speed
    analogWrite(E2, 200);   // PWM regulate speed
    delay(8000);
    digitalWrite(M1,LOW);  
    digitalWrite(M2, LOW);      
    analogWrite(E1, 200);   //PWM regulate speed
    analogWrite(E2, 200);   //PWM regulate speed
    delay(8000);
}


Test Result

Upload well the code, you should see the two motors firstly turn forward for 8 seconds, then reverse for 8 seconds, repeatedly.
File:KS0007 result.png

Resources

Video
http://www.keyestudio.com/wp/ks0007/

PDF
https://drive.google.com/open?id=1yU9UR8Nd2pfKEiHc0vDGMtQtOl56GoC6


Get One Now

Official Website
http://www.keyestudio.com/ks0007.html

Amazon Store
https://www.amazon.com/Shield-current-driver-module-Arduino/dp/B016PNP93I/