Ks0153 keyestudio JoyStick Shield

Keyestudio JoyStick Shield

Introduction

Keyestudio Joystick Shield is particularly developed for you to design your own game machines.
It adds an nRF24L01 RF interface and Nokia 5110 LCD interface, easy for secondary game development. Because this RF module has stable performance, and supports 6 in 1 game play, which allows developers to play freely. Nokia 5110 LCD is widely used in various development platforms, with highly cost-effective and has a strong library support. Here, we add enhanced Nokia5110 display library, including display bitmap, draw point line circle flip and so on.
It also adds a Bluetooth module interface, for convenient Bluetooth wireless serial communication, and a I2C communication interface for I2C devices connection.
Meanwhile, JoyStick Shield has a cross-shape PS2 joystick with button. There are four round buttons, 2 small buttons, providing input expansion for Arduino joystick and buttons. Onboard slide switch can switch between 3.3V and 5V.

Specification

• Compatible with UNO R3 and MEGA 2560 control board.
• Comes with a joystick button: X- (connected to A0); Y- (connected to A1); button (connected to D8).
• 4 round buttons with cap: button A (D2); button B (D3); button C (D4); button D (D5).
• 2 small buttons: button E (D6); button F (D7)
• A slide switch: control the output voltage of V end for 3.3V or 5V. (Note: V end can also power up the joystick element)
• Adds a nRF24L01 interface
• Adding Nokia 5110 LCD headers
• Adding Bluetooth module interface

PCB Dimensions

Pinout Instructions

Connect it Up

Stack well the shield onto UNO R3 board, slide the switch to 5V.

Upload the Code

Below is an example code, you can copy and paste it on Arduino IDE.

• Download Arduino IDE
• Install Arduino Driver

void setup()
{
  for(int i=2; i<9; i++)
  { 
    pinMode(i, INPUT);
    digitalWrite(i, 1);
  }  
  Serial.begin(9600);  
}
void loop(){
  int i, someInt, flag = 0;
  for(i=2; i<9; i++)
  {
    someInt = digitalRead(i);
    if(someInt == 0)
    {  
      flag =1;
      break;
    }
   }
   if(flag == 1)
   {    
     switch(i)
     {
       case 2: Serial.println("--------> Button A"); break;
       case 3: Serial.println("--------> Button B"); break;
       case 4: Serial.println("--------> Button C"); break;
       case 5: Serial.println("--------> Button D"); break;
       case 6: Serial.println("--------> Button E"); break;
       case 7: Serial.println("--------> Button F"); break;
       case 8: Serial.println("--------> Button KEY"); break;
       default: break;
     }
     flag=0;
     delay(200);
   }
   int sensorValue1 = analogRead(A0);
   Serial.print("X = ");
   Serial.println(sensorValue1 ); 
   int sensorValue2 = analogRead(A1);
   Serial.print("Y = ");
   Serial.println(sensorValue2);  
   delay(200);
}

What You Should See?

Upload the above code to the board, open the serial monitor and set the baud rate as 9600.
You should see the X, Y data of joystick element. Press the button A,B,C and D, the data will be displayed on the monitor.

For Applications

Plug the joystick shield onto keyestudio UNO R3 board, you can connect a LCD and temperature and humidity sensor to build the circuit experiment.

Resources

https://fs.keyestudio.com/KS0153

Get One Now

• Official Website

• From Aliexpress store:

• From eBay store: