KS5014 Keyestudio 2560 WIFI PLUS Main Board: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
(Created blank page)
 
No edit summary
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:


<br>[[File:2560 WIFI PLUS.png|500px|right|frameless|thumb]]<br>
== Introduction ==
<br>
Keyestudio 2560 WIFI PLUS Main Control Board adopts two MCU including ATmega 2560 and esp8266, containing all functions of Arduino Mega 2560and ESP8266 development board.<br> <br>
The two MCU combination is suitable for the development of the Internet of Things, networking functions, and independent wireless network construction.<br><br>
The download function of the serial port is controlled by the toggle switch, and the codes of the two MCU can be burned separately by using a USB interface so that two development boards can be used alone or combined. It is very convenient when using.<br>
<br><br>
== Parameters ==
{| class="wikitable"
|+
|-
| Working Voltage || USB/5V; DC/6-9V (Esp8266/3.3V; ATmega 2560/5V)
|-
| Working Current || Maximum output 3.3V/800mA or 5V/1.6A
|-
| Maximum Power || 8W
|-
| Working Temperature Range || -10~50 °C
|-
| Dimensions || 103*53.5*13mm
|-
| Environmental Attributes || ROHS
|-
| ATmega 2560 Digital I/O || 54 pin (15 for PWM output; D20,D21 as regular I2C)
|-
| ATmega 2560 PWM Digital I/O || 15 pin
|-
| ATmega 2560  Analog Input Pin || 16 pin
|-
| DC of each ATmega 2560 I/O Pin || 20mA
|-
| ATmega 2560 flash || 256KB(8KB used for bootloader)
|-
| ATmega 2560 SRAM || 8KB
|-
| ATmega 2560 EEPROM || 4KB
|-
| ATmega 2560 Clock Speed || 16MHZ
|-
| Esp8266 Digital I/O || 9 on-board pin
|-
| Esp8266 PWM Digital I/O || 4 pin (IO4,IO12,IO14,IO15)
|-
| DC of each Esp8266 I/O Pin || 20mA
|-
| Esp8266 flash || 2MB
|-
| Esp8266 SRAM || 50kb
|-
| Esp8266 Clock Speed || 26MHZ
|-
| Esp8266 Radio Frequency || 2.4GHZ Receiver and Transmitter
|-
| Wifi || ESP8266EX supports TCP/IP protocol and 802.11 b/g/n WLAN MAC protocol.<br> Supports Basic Service Set (BSS) STA and SoftAP operation under Distributed Control Function (DCF).<br> Enables optimization of active hours by minimizing host interaction for power management.
|}
<br><br>
== Interfaces and Components Description ==
<br>[[File:5014Interfacesandcomponentsdescription.png|600px|frameless]]<br>
<br>
== Special Function Interface ==
{| class="wikitable"
|+
|-
| '''Serial Communication''' || Port 0  D0(RX) and D1(TX)<br>Port 1  D19(RX) and D18(TX)<br>Port 2  D17(RX) and D16(TX)<br>Port 3  D15(RX) and D14(TX)
|-
| '''External Interrupt''' || D2(Interrupt 0), D3(Interrupt1), D18(Interrupt5), D19(Interrupt4), D20(Interrupt3) and D21(Interrupt2)
|-
| '''PWM Interface''' || D2-D13 and D44-D46
|-
| '''SPI Communication''' || D53(SS), D51(MOSI), D50(MISO), D52(SCK)
|-
| '''IIC Communication''' || D20(SDA), D21(SCL）
|-
| '''ICSP Interface''' || ATMEGA2560-16AU Interface for burning firmware
|-
| '''USB Interface''' || downloading programs and serial port debugging
|-
| '''DC Power Interface''' || able to connect to DC6V-9V
|-
| '''Power Output Interface''' || 3.3V/5V output, often used for external power supply or common ground processing
|-
| '''Analog Interface''' || A0-A15
|}
<br>
'''ESP8266 pin'''
(Logo of the board as the positive direction, pin attributes from left to right)
{| class="wikitable"
|+
|-
| VCC || RST || CH-PD || TX0 || GPIO5 || GPIO4 || GPIO12
|-
| RX0 || GPIO0 || GPIO2 || GND || GPIO16 || TOUT || GND
|}
<br>
'''DIP Switch Description (ON/OFF)'''
<br>[[File:0(~U( JE-L$-4`OU1CA7O17.png|600px|frameless]]<br>
<br>
== Projects ==
<br>
=== Arduino 2560 Burn Test Program ===
<br>
Connect PLUS main control board to computer with USB cable.
Taking Keyestudio LOGO as a reference, toggle the switch to the left for on and right for off.<br><br>
The positions of the 16-pin DIP switch and the 6-pin DIP switch are shown below:<br>
<br>[[File:5014pinpositions.png|600px|frameless]]<br><br>
Open [[File:5014-2560.jpg|600px|frameless]] under code\2560.<br>
<br>[[File:-SFC4GO)--38$TM@1-1@A7M111111111.png|600px|frameless]]<br><br>
Choose the development board "Arduino Mega or Mega 2560" and port.<br>
<br>[[File:-5F--P20M0Q30 6-D4-EMOK1111111111112.png|600px|frameless]]<br><br>
Click [[File:5014click1.png|600px|frameless]] to upload the program to PLUS main control board, and wait for a prompt of successful uploading in the lower left corner.<br><br>
Then click [[File:5014click2.png|600px|frameless]] to open the watch window and set baud rate at 115200; send sequentially:<br><br>
a: lighting test (D13)<br>
b: memory test<br>
c: pin test<br>
<br>[[File:PL~HDUY1DS2-~JD-3VMZYG011111111113.png|600px|frameless]]<br><br>
=== ESP8266 Burn Test Program ===
<br>
Connect PLUS main control board to computer with USB cable.
Taking Keyestudio LOGO as a reference, toggle the switch to the left for on and right for off.<br><br>
The positions of the 16-pin DIP switch and the 6-pin DIP switch (toggle to serial port 1) are shown below:<br>
<br>[[File:5014pinpositions2.jpg|600px|frameless]]<br><br>
Open [[File:5014-esp8266.jpg|600px|frameless]] under code\esp8266, and turn on the WIFI network sharing of the mobile phone or computer and set the name and password to be consistent with those in the program.<br><br>
[[File:JRXD8S8@GHCS)GIV4F @A~722222221.png|600px|frameless]]<br><br>
Choose the development board "Generic ESP8266 Module" and port.<br>
<br>[[File:U)ES(~LHV6GKMDCE8CS~U5T2222222.png|600px|frameless]]<br><br>
Click [[File:5014click1.png|600px|frameless]] to upload the program to PLUS main control board, and wait for a prompt of successful uploading in the lower left corner.<br>
If the upload fails, unplug the USB cable and reconnect it before uploading.<br><br>
NOTE: Before each programming of esp8266, the switch must be toggled at GND-GPIO0, and it can be used as a normal IO port if turn it off after programming.<br>
<br>[[File:$Y-M3AG8ZC4J%N-M1Z31$DG2222223.png|600px|frameless]]<br><br>
Test result:<br><br>
The positions of 16-pin and 6-pin DIP switch are shown below:<br>
<br>[[File:5014pinpositions3.jpg|600px|frameless]]<br><br>
Click [[File:5014click2.png|600px|frameless]] to open the watch window and set baud rate at 115200. After the ESP8266 of the main control board is connected to WIFI, the IP address is printed out on the monitoring serial port (Press RESERT button if not).<br>
<br>[[File:QOP8O(TPW1)Q8WKS )~W0@S222224.png|600px|frameless]]<br><br>
=== TEST_MEGA-ESP Remote Control ===
Upload the project on Chapter 7.2, and choose the development board when uploading. <br><br>
Upload code "TEST_MEGA-ESP.ino" to the main control board and choose the development board "Arduino Mega or Mega 2560". <br><br>
After successful uploading. Toggle the switch to the position shown below: <br><br>
[[File:5014pinpositions4.jpg|600px|frameless]]<br><br>
Open Hotpot and connect ESP8266 to WIFI network.<br><br>
And open the serial port after successful connecting, IP address will be displayed. <br><br>
Open this address of 8266 on any browser, the [ON] [OFF] of LED state will control the onboard LED on 2560 and ESP8266.<br>
<br>[[File:-XC2D$9KMVEA8DW~K0CJJ9V333331.png|600px|frameless]]<br>
<br>[[File:H-`FD0)XI$2I3$PIJ7-DSBO33332.png|600px|frameless]]<br><br>
== Resources ==
<br>
For more details, please refer to:<br><br>
https://fs.keyestudio.com/KS5014
<br>

Latest revision as of 11:53, 17 March 2023


thumb


Introduction


Keyestudio 2560 WIFI PLUS Main Control Board adopts two MCU including ATmega 2560 and esp8266, containing all functions of Arduino Mega 2560and ESP8266 development board.

The two MCU combination is suitable for the development of the Internet of Things, networking functions, and independent wireless network construction.

The download function of the serial port is controlled by the toggle switch, and the codes of the two MCU can be burned separately by using a USB interface so that two development boards can be used alone or combined. It is very convenient when using.


Parameters

Working Voltage USB/5V; DC/6-9V (Esp8266/3.3V; ATmega 2560/5V)
Working Current Maximum output 3.3V/800mA or 5V/1.6A
Maximum Power 8W
Working Temperature Range -10~50 °C
Dimensions 103*53.5*13mm
Environmental Attributes ROHS
ATmega 2560 Digital I/O 54 pin (15 for PWM output; D20,D21 as regular I2C)
ATmega 2560 PWM Digital I/O 15 pin
ATmega 2560 Analog Input Pin 16 pin
DC of each ATmega 2560 I/O Pin 20mA
ATmega 2560 flash 256KB(8KB used for bootloader)
ATmega 2560 SRAM 8KB
ATmega 2560 EEPROM 4KB
ATmega 2560 Clock Speed 16MHZ
Esp8266 Digital I/O 9 on-board pin
Esp8266 PWM Digital I/O 4 pin (IO4,IO12,IO14,IO15)
DC of each Esp8266 I/O Pin 20mA
Esp8266 flash 2MB
Esp8266 SRAM 50kb
Esp8266 Clock Speed 26MHZ
Esp8266 Radio Frequency 2.4GHZ Receiver and Transmitter
Wifi ESP8266EX supports TCP/IP protocol and 802.11 b/g/n WLAN MAC protocol.
Supports Basic Service Set (BSS) STA and SoftAP operation under Distributed Control Function (DCF).
Enables optimization of active hours by minimizing host interaction for power management.



Interfaces and Components Description


5014Interfacesandcomponentsdescription.png

Special Function Interface

Serial Communication Port 0 D0(RX) and D1(TX)
Port 1 D19(RX) and D18(TX)
Port 2 D17(RX) and D16(TX)
Port 3 D15(RX) and D14(TX)
External Interrupt D2(Interrupt 0), D3(Interrupt1), D18(Interrupt5), D19(Interrupt4), D20(Interrupt3) and D21(Interrupt2)
PWM Interface D2-D13 and D44-D46
SPI Communication D53(SS), D51(MOSI), D50(MISO), D52(SCK)
IIC Communication D20(SDA), D21(SCL）
ICSP Interface ATMEGA2560-16AU Interface for burning firmware
USB Interface downloading programs and serial port debugging
DC Power Interface able to connect to DC6V-9V
Power Output Interface 3.3V/5V output, often used for external power supply or common ground processing
Analog Interface A0-A15


ESP8266 pin (Logo of the board as the positive direction, pin attributes from left to right)

VCC RST CH-PD TX0 GPIO5 GPIO4 GPIO12
RX0 GPIO0 GPIO2 GND GPIO16 TOUT GND


DIP Switch Description (ON/OFF)
0(~U( JE-L$-4`OU1CA7O17.png

Projects



Arduino 2560 Burn Test Program


Connect PLUS main control board to computer with USB cable. Taking Keyestudio LOGO as a reference, toggle the switch to the left for on and right for off.

The positions of the 16-pin DIP switch and the 6-pin DIP switch are shown below:

5014pinpositions.png

Open 5014-2560.jpg under code\2560.

-SFC4GO)--38$TM@1-1@A7M111111111.png

Choose the development board "Arduino Mega or Mega 2560" and port.

-5F--P20M0Q30 6-D4-EMOK1111111111112.png

Click 5014click1.png to upload the program to PLUS main control board, and wait for a prompt of successful uploading in the lower left corner.

Then click 5014click2.png to open the watch window and set baud rate at 115200; send sequentially:

a: lighting test (D13)
b: memory test
c: pin test

PL~HDUY1DS2-~JD-3VMZYG011111111113.png

ESP8266 Burn Test Program


Connect PLUS main control board to computer with USB cable. Taking Keyestudio LOGO as a reference, toggle the switch to the left for on and right for off.

The positions of the 16-pin DIP switch and the 6-pin DIP switch (toggle to serial port 1) are shown below:

5014pinpositions2.jpg

Open 5014-esp8266.jpg under code\esp8266, and turn on the WIFI network sharing of the mobile phone or computer and set the name and password to be consistent with those in the program.

JRXD8S8@GHCS)GIV4F @A~722222221.png

Choose the development board "Generic ESP8266 Module" and port.

U)ES(~LHV6GKMDCE8CS~U5T2222222.png

Click 5014click1.png to upload the program to PLUS main control board, and wait for a prompt of successful uploading in the lower left corner.
If the upload fails, unplug the USB cable and reconnect it before uploading.

NOTE: Before each programming of esp8266, the switch must be toggled at GND-GPIO0, and it can be used as a normal IO port if turn it off after programming.

$Y-M3AG8ZC4J%N-M1Z31$DG2222223.png

Test result:

The positions of 16-pin and 6-pin DIP switch are shown below:

5014pinpositions3.jpg

Click 5014click2.png to open the watch window and set baud rate at 115200. After the ESP8266 of the main control board is connected to WIFI, the IP address is printed out on the monitoring serial port (Press RESERT button if not).

QOP8O(TPW1)Q8WKS )~W0@S222224.png

TEST_MEGA-ESP Remote Control

Upload the project on Chapter 7.2, and choose the development board when uploading.

Upload code "TEST_MEGA-ESP.ino" to the main control board and choose the development board "Arduino Mega or Mega 2560".

After successful uploading. Toggle the switch to the position shown below:

5014pinpositions4.jpg

Open Hotpot and connect ESP8266 to WIFI network.

And open the serial port after successful connecting, IP address will be displayed.

Open this address of 8266 on any browser, the [ON] [OFF] of LED state will control the onboard LED on 2560 and ESP8266.

-XC2D$9KMVEA8DW~K0CJJ9V333331.png

H-`FD0)XI$2I3$PIJ7-DSBO33332.png

Resources


For more details, please refer to:

https://fs.keyestudio.com/KS5014

Retrieved from "http://wiki.keyestudio.com/index.php?title=KS5014_Keyestudio_2560_WIFI_PLUS_Main_Board&oldid=34701"