Search results

Jump to navigation Jump to search
  • ...ge:KS0350 (6).jpg|thumb|400px|right|Keyestudio KEYBOT Coding Robot Control Board]] The Keyestudio KEYBOT Coding Robot Control Board is particularly designed for car robot control. <br>
    11 KB (1,706 words) - 13:53, 30 April 2021
  • ...0386.png|thumb|300px|right|keyestudioESP-01S Wifi Module Adapter Board for Arduino]] This is an expansion board for the ESP-01S WiFi module, compatible with the breadboard. <br>
    3 KB (385 words) - 11:47, 6 January 2021
  • ...ontains 24 commonly used sensors/modules, a ESP32 board, a ESP32 expansion board and Dupont wires.<br> ...Board. You only need to stack the ESP32 mainboard onto the ESP32 Expansion Board, and hook up them with Dupont wires, which is simple and convenient.<br>
    3 KB (357 words) - 16:51, 20 May 2022
  • The mega 2560 control board, among the series of MCUs , is the most popular since it has numerous pins. ...development board. In fact, its use method is as same as the official mega board, in addition to the different volume.
    10 KB (1,563 words) - 10:13, 30 April 2021
  • This module should be used together with EASY plug control board.<br> ...plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has d
    3 KB (422 words) - 16:48, 7 January 2021
  • Step 1: wire up the USB to serial module and the ESP32-CAM development board ...ntrol board.(USB cable can’t supply large current to drive the development board, thus, the external power more than 5V 500mA is needed.)
    6 KB (880 words) - 10:11, 7 January 2022
  • ...TMEGA2560-16AU which is compatible with the Arduino MEGA 2650 development board. Integrated with 2 TB6612 motor driving chips, this processor can be served <br>In addition, the output power supply of this board can reach the maximum 5V 3A, in 3 channels (good heat dissipation).Through
    10 KB (1,692 words) - 15:20, 28 December 2021
  • ==Keyestudio 3D MKS Gen V1.4 Printer Motherboard Control Board== ...solutionof the RAMPS 1.4 and Arduino Mega 2560 board on a fantastic single board. <br>
    8 KB (1,268 words) - 15:18, 7 January 2021
  • ...r supply, connect the SIG pin of the module to the PWM port of the arduino board, set the PWM value, and adjust the magnetic field of the module. The larger Connect up this module and UNO board like this: SIG pin to Digital port 3, VCC pin to 5V, GND pin to the ground
    4 KB (529 words) - 11:41, 25 March 2021
  • [[image:KS0354.png|thumb|500px|right|Keyestudio ESP8266 WI-FI Development Board]] This keyestudio ESP8266 WI-FI development board is based on the ESP8266-12FWIFI module developed by Ai-Thinker. <br>
    11 KB (1,749 words) - 14:53, 17 November 2021
  • ...When you knock it, it can send a momentary signal. You can combine it with Arduino to make some interesting experiment, e.g. electronic drum. ...r detects a knock signal, both the led on the sensor and led 13 on the UNO board are turned on.
    2 KB (242 words) - 14:45, 7 January 2021
  • ...8266, containing all functions of Arduino Mega 2560and ESP8266 development board. The two MCU combination is suitable for the development of the Internet of
    1 KB (233 words) - 11:54, 17 February 2023
  • Keyestudio CNC Shield V2.0 can be used as driver expansion board for engraving machines . It has in total 3 channel slots for A4988 stepper 2. GRBL 0.8c compatible. (Open source firmware that runs on an Arduino V4.0 board that turns G-code commands into stepper signals)
    12 KB (1,837 words) - 14:47, 25 November 2020
  • ...circuit. Its voltage can be subdivided into 1023, easy to be connected to Arduino with our sensor shield. <br> This module should be used together with EASY plug control board.</span><br>
    4 KB (549 words) - 16:02, 7 January 2021
  • Keyestudio CNC Shield V3.0 can be used as driver expansion board for engraving machines . It has in total 4 channel slots for A4988 stepper * GRBL 0.8c compatible. (Open source firmware that runs on a keyestudio V4.0 board that turns G-code commands into stepper signals)
    12 KB (1,816 words) - 14:13, 25 November 2020
  • The driver chip of this board is CH340, which is not compatible with mac system computer. ...ight click “Computer” —> “Properties”—> “Device manager”, you can see the Board and Com port as below figure shown.
    5 KB (762 words) - 17:50, 29 January 2021
  • [[image:KS0350 (3).jpg|thumb|400px|right|KEYBOT Coding Robot Control Board Kit]] The Keyestudio KEYBOT Coding Robot Control Board is particularly designed for car robot control. <br>
    11 KB (1,796 words) - 08:14, 30 April 2021
  • Arduino Relay Shield employs high quality SONGLE relay with two-channel input and o The modularized design makes it easy to connect to Arduino expansion board. The output state of the relay is shown by a LED for the convenience of
    2 KB (310 words) - 14:29, 21 November 2022
  • keyestudio Pro Mini is a small microcontroller board based on the ATmega328. ([http://ww1.microchip.com/downloads/en/DeviceDoc/A Note that the board is without an on-board USB to Serial connection. To program the Pro Mini, you will need an externa
    12 KB (1,964 words) - 10:31, 6 January 2021
  • ...urrent time, so that you know exactly when something happened! Unlike most Arduino Data Logging shield, this one is backed up by a supercapacitor instead of a ...duino development board when using and does not affect the IO ports of the board
    3 KB (497 words) - 17:08, 16 June 2023

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)