Search results
Jump to navigation
Jump to search
- [[image:KS0248.jpg|thumb|900px|right|Keyestudio Leonardo R3 Development Board ]] The keyestudio Leonardo is a microcontroller board based on the ATmega32u4 ([https://www.microchip.com/wwwproducts/en/atmega3214 KB (2,273 words) - 11:38, 29 April 2021
- This keyestudio microphone module is fully compatible with micro:bit control board. It is a sound detection device, an analog signal output device.<br> When using, connect the module to micro:bit control board using Crocodile clip line.3 KB (423 words) - 11:02, 4 March 2021
- ...eyestudio TEMT6000 light module is fully compatible with micro:bit control board. <br> When using, connect the module to micro:bit control board using Crocodile clip line.<br>3 KB (411 words) - 11:06, 4 March 2021
- [[image:0468-1.png|thumb|900px|right|Keyestudio PRO MICRO Development Board ]] In order to carry it conveniently, we put a micro: bit control board and two manuals in storage bag. The storage bag is light and beautiful.4 KB (542 words) - 09:03, 27 April 2021
- keyestudio CAN-BUS Shield is particularly designed for Arduino controllers. <br> ...ard interface; can be perfectly adapted to the main control boards such as Arduino UNO and Leonardo.As shown below.<br>7 KB (927 words) - 11:58, 6 January 2021
- ...cro bit honeycomb photoresistor is fully compatible with micro bit control board. In the experiment, we connect it with the micro: bit by a crocodile clip. ...During the test, we test the analog value of S end via micro: bit control board. The brighter the light is, the larger the analog value is, the darker the2 KB (293 words) - 10:56, 22 January 2021
- ''' Keyestudio Mega 2560 board：''' <br> Keyestudio Mega 2560 R3 is a microcontroller board based on the ATMEGA2560. It has 54 digital input/output pins (of which 159 KB (1,407 words) - 15:10, 7 January 2021
- ...assets of the RAMPS 1.4 and Arduino Mega 2560 boards on a fantastic single board solution. The MKS Base 1.2 is an optimal 3D printer controller solution for It contains a SD-Card reader. You can easy connect it to your Ramps board using the ""smart adapter"" included. After connecting this panel to your R8 KB (1,266 words) - 15:14, 7 January 2021
- ==keyestudio Scratch for Arduino Starter Kit== ...children can program themselves by Scratch to make Arduino perform or use Arduino to get data measured by external sensors; therefore, they can create their16 KB (2,501 words) - 15:50, 6 January 2021
- The newly upgraded 4WD Multi-purpose car is one of the most popular Arduino sets. It not only has a beautiful appearance but also powerful functions. I ...learning projects, from simple to complex, which will guide you to make an Arduino robot. <br>3 KB (431 words) - 14:44, 10 August 2022
- ...ds to work with Keyestudio nano ch340 . It can be used as driver expansion board for engraving machines. It has in total 3 channel slots for A4988 stepper m keyestudio nano ch340 controller is a small, complete board based on the ATmega328. It’s a open source Simple I/O platform with 12 Di14 KB (2,193 words) - 10:29, 28 April 2021
- ...uits, suitable for a variety of development boards and controllers such as Arduino controller, STC single-chip microcomputer, AVR single-chip microcomputer, e ...plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has d4 KB (574 words) - 15:57, 7 January 2021
- sensors/modules, the Raspberry Pi Pico board, the Raspberry Pi Pico expansion board and Dupont wires. <br> ...the Raspberry Pi Pico shield. You only need to stack the Raspberry Pi Pico board onto the Raspberry Pi Pico shield, and hook up them with Dupont wires, whic5 KB (638 words) - 14:02, 31 December 2021
- ...rface to communicate. When using it, directly stack it onto UNO R3 control board. ...tp://wiki.keyestudio.com/index.php/Ks0001_keyestudio_UNO_R3_BOARD UNO R3 board ]. <br>5 KB (772 words) - 14:24, 6 January 2021
- You can refer to the following connection. For UNO board and pressure sensor, connect the S pin of sensor to A0, negative pin to GND ...://wiki.keyestudio.com/index.php/Download_Arduino_IDE_and_Install_Driver Arduino IDE ].3 KB (364 words) - 12:18, 7 January 2021
- ...ed out as Registered Jack, allowing you to connect it to EASY plug Control board V2.0 for communication with only an RJ11 cable. <br> ...plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has d5 KB (763 words) - 08:54, 8 January 2021
- You can download different version of Arduino IDE from the link here:<br> https://www.arduino.cc/en/Main/OldSoftwareReleases#1.5.x <br>6 KB (793 words) - 11:58, 4 March 2021
- ...UNO_R3_BOARD UNO R3 ]. So you just need to stack it onto UNO R3 control board when using. <br> To easily debug the operating mode of stepper motor driver board, there are 3 jumper caps under each pin slots. You can set the working mode5 KB (692 words) - 10:40, 29 April 2021
- ...UNO_R3_BOARD UNO R3 ]. So you just need to stack it onto UNO R3 control board when using. <br> To easily debug the operating mode of stepper motor driver board, there are 3 jumper caps under each pin slots. You can set the working mode5 KB (700 words) - 13:31, 14 August 2018
- You can connect the module to control board for communication using jumper wires.<br> ...g the code, do remember to place the Matrix library folder into directory \Arduino\libraries. Otherwise, fail to compile the code. <br>4 KB (599 words) - 10:05, 8 January 2021